The suspension damper solenoid is driven ON and OFF by the electronic suspension control (ESC) module. To activate the suspension damper solenoid it is initially subjected to full battery voltage for a short period of time. Once the suspension damper solenoid is pulled-in the supply voltage is pulse width modulated (PWM). The amount the suspension damper solenoid valve is activated is based on inputs from the driver Tow/Haul Switch, road inputs, position sensor inputs and the powertrain control module (PCM).
The ESC module performs a test on each suspension damper solenoid during both the ON and OFF states.
• | A short to ground in the control circuit of the suspension damper solenoid |
• | A short to voltage in the control circuit of the suspension damper solenoid |
• | An open in the control circuit of the suspension damper solenoid |
• | An open in the solenoid low reference circuit of the suspension damper solenoid |
• | A short to voltage in the solenoid low reference circuit of the suspension damper solenoid |
• | The suspension damper solenoid will be disabled. |
• | All suspension damper solenoids will be disabled. |
• | The SERVICE RIDE CONTROL message will be displayed. |
• | Stores a DTC C0575, C0580, C0585 or C0590 in the ESC module memory. |
• | The ESC module no longer detects a problem in the low reference circuit or the control circuit of the suspension damper solenoid. |
• | Using the scan tool. |
• | A history DTC will clear after 100 consecutive ignition cycles if the condition for the malfunction is no longer present. |
Important: Ignition cycle counting is used by the ESC module to detect faults in the system. The objective is to eliminate false/intermittent codes while maintaining an acceptable level of system performance. The operation of the ignition cycle counting requires that a fault condition be present for four consecutive ignition cycles before it will set the fault code and display the "SERVICE RIDE CONTROL" message. If a fault code is present (without a fault being current), the system will go into one or more degraded modes without displaying a message. Resetting the ignition cycle counter is done by clearing codes with a scan tool. Clearing codes will override ignition cycle counting for one ignition cycle. Therefore, a fault condition will set the fault code immediately if it occurs on the first ignition cycle after the codes are cleared.
If DTC C0870 or C0690 is present, repair the malfunction for these DTCs before diagnosing DTC C0575, C0580, C0585 or C0590.
It may be necessary to check Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
The numbers below refer to the step numbers on the diagnostic table.
Tests for low reference circuit of the suspension damper solenoid. The ESC module supplies ground of the suspension damper solenoid.
Verifies that the resistance of the suspension damper solenoid.
Tests the control circuit to the suspension damper solenoid for an open and short to voltage.
Tests the control circuit for a short to ground.
Replace and program the ESC module.
Step | Action | Value(s) | Yes | No |
---|---|---|---|---|
Schematic Reference: Suspension Controls Schematics | ||||
1 |
Important: If DTC C0870 or DTC C0690 is present, perform the diagnosis for these DTCs first. Did you perform the ESC Diagnostic System Check? | -- | Go to Step 2 | Go to Diagnostic System Check - Electronic Suspension Control |
Does the test lamp illuminate? | -- | Go to Step 3 | Go to Step 8 | |
Does the resistance of the shock absorber measure within the specified value? | 1.5-3.3 ohms | Go to Step 4 | Go to Step 6 | |
Test the control circuit of the suspension damper solenoid for a short to voltage and an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 11 | Go to Step 5 | |
Test the control circuit of the suspension damper solenoid for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 11 | Go to Step 7 | |
6 | Inspect for poor connections at the suspension damper solenoid. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 9 |
7 | Inspect for poor connections at the harness connector of the ESC module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 11 | Go to Step 10 |
8 | Test the low reference circuit of the suspension damper solenoid for an open and short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 11 | Go to Step 10 |
9 | Replace the shock absorber. Refer to Shock Absorber Replacement in Front Suspension or Shock Absorber Replacement in Rear Suspension. Did you complete the replacement? | -- | Go to Step 11 | -- |
Replace the ESC module. Refer to Electronic Suspension Control Module Replacement . Did you complete the replacement? | -- | Go to Step 11 | -- | |
11 |
Does the DTC reset? | -- | Go to Step 2 | System OK |