Schematic Reference: Interior Lights Dimming Schematics

Connector End View Reference: Master Electrical Component List in Wiring Systems

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

1. Place the headlamp switch in the PARK position.
2. Operate the Instrument Panel (I/P) dimmer switch.

Do the instrument panel lamps operate properly?

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

Go to Step 3

1. Place the headlamp switch in the OFF position.
2. Disconnect the I/P dimmer switch.
3. Probe the park lamp supply voltage circuit of the I/P dimmer switch with a test lamp that is connected to a good ground.
4. Place the headlamp switch in the PARK position.

Does the test lamp illuminate?

Go to Step 4

Go to Step 10

1. Place the headlamp switch in the OFF position.
2. Connect a 15-amp fused jumper wire between the park lamp supply voltage circuit of the I/P dimmer switch and the instrument panel lamps dimmer switch signal circuit of the I/P dimmer switch connector.
3. Place the headlamp switch in the PARK position.

Do the instrument panel lamps illuminate?

Go to Step 8

Go to Step 5

1. Leave the fused jumper wire connected.
2. Place the headlamp switch in the OFF position.
3. Disconnect the I/P dimming module.
4. Probe the instrument panel lamps dimmer switch signal circuit of the I/P dimmer switch at the I/P dimming module connector with a test lamp that is connected to a good ground.
5. Place the headlamp switch in the PARK position.

Does the test lamp illuminate?

Go to Step 6

Go to Step 11

Connect a 15-amp fused jumper wire between the instrument panel lamps dimmer switch signal circuit of the I/P dimmer switch and the instrument panel lamps dimmer switch signal circuit of the I/P dimming module at the I/P dimming module connector.

Are the instrument panel lamps illuminated?

Go to Step 7

Go to Step 12

Test the park lamp supply voltage circuit of the I/P dimming module for an open, high resistance, or short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 15

Go to Step 9

Inspect for poor connections at the harness connector of the I/P dimmer switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 15

Go to Step 13

Inspect for poor connections at the harness connector of the I/P dimming module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 15

Go to Step 14

Repair an open, high resistance, or short to ground in the park lamp supply voltage circuit of the I/P dimmer switch. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 15

--

Repair an open, high resistance, or short to ground in the instrument panel lamps dimmer switch signal circuit of the I/P dimmer switch. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 15

--

Repair an open, high resistance, or short to ground in the instrument panel lamps dimmer switch signal circuit of the I/P dimming module. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 15

--

Replace the I/P dimmer switch. Refer to Instrument Panel Lamp Dimmer Switch Replacement .

Did you complete the replacement?

Go to Step 15

--

Replace the I/P dimming module. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.

Did you complete the replacement?

Go to Step 15

--

Operate the system in order to verify the repair.

Did you correct the condition?

System OK

Go to Step 3