GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2006 🢒 Classic 🢒 HVAC 🢒 HVAC Systems - Manual 🢒 Too Cold in Vehicle

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. This step inspects for proper cooling system operation.

    2.

  2. The voltage will vary between 0-12 volts during normal operation. The HVAC control assembly connector must be connected during this step.

Step

Action

Values

Yes

No

Schematic Reference: HVAC Schematics

Connector End View Reference: HVAC Connector End Views

DEFINITION: The temperature cannot be adjusted, or the heating is insufficient.

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2
  1. Turn ON the ignition, with the engine OFF.
  2. Place the blower control in each speed position.

Does the blower motor operate in any of the speed positions?

--

Go to Step 3

Go to Blower Motor Inoperative

3

Does the blower motor operate in the desired speed?

--

Go to Step 4

Go to Blower Motor Malfunction

4
  1. Place the mode switch in the vent position.
  2. Place the blower motor switch in the maximum speed position.
  3. Place the outside air switch in the ON position.
  4. Place the recirculation switch in the ON position.

Does the recirculation door move from the recirculation position to the outside air position?

--

Go to Step 5

Go to Air Recirculation Malfunction

5

Inspect the cooling system for the following:

    • A low coolant level
    • A loose or worn accessory drive belt
    • A leaking radiator or heater hoses
    • A kinked radiator or heater hoses
    • A missing radiator filler cap pressure seal
    • A leaking radiator cap

Did you find and correct the condition?

--

Go to Step 18

Go to Step 6

6
  1. Start the engine.
  2. Place the mode switch in the OFF, or HEAT positions.

Does the A/C compressor operate?

--

Go to HVAC Compressor Clutch Does Not Disengage

Go to Step 7

7
  1. Turn ON the ignition, with the engine OFF.
  2. Observe the air temperature actuator drive shaft.
  3. Place the air temperature switch from the coldest position to the warmest position.

Does the air temperature actuator drive shaft rotate at all?

--

Go to Step 8

Go to Step 9

8

Inspect the air temperature door and the air temperature actuator for the following conditions:

    • Misaligned air temperature actuator--Refer to Air Temperature Actuator Replacement .
    • Broken or binding linkages or air temperature door
    • Obstruction that prevents the air temperature door from operating within its full range of motion
    • Missing seals to the air temperature door
    • Misaligned seals to the air temperature door

Did you find and correct the condition?

--

Go to Step 18

Go to Step 9

9

Test the ignition 3 voltage circuit of the air temperature actuator for an open or a high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 18

Go to Step 10

10

Test the ground circuit of the air temperature actuator for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 18

Go to Step 11

11

Test the air temperature door position signal circuit of the air temperature actuator for an open, high resistance, short to ground, or short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 18

Go to Step 12

12

Important:: Ensure that the HVAC control assembly connector is connected during this step in order to avoid misdiagnosis.

  1. Turn ON the ignition, with the engine OFF.
  2. Measure the voltage from the air temperature door position signal circuit of the air temperature actuator to a good ground.
  3. Place the air temperature switch from the coldest position to the warmest position.

Does the voltage measure within the specified values with a smooth transition between COLD to HOT?

0-12 V

Go to Step 15

Go to Step 13

13

Inspect for poor connections at the harness connector of the air temperature actuator. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 18

Go to Step 14

14

Inspect the air temperature actuator, door and any attaching linkage for binding or a condition that prevents drive shaft rotation.

Did you find and correct the condition?

--

Go to Step 18

Go to Step 16

15

Inspect for poor connections at the harness connector of the HVAC control assembly. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 18

Go to Step 17

16

Replace the air temperature actuator. Refer to Air Temperature Actuator Replacement .

Did you complete the replacement?

--

Go to Step 18

--

17

Replace the HVAC control assembly. Refer to Heater and Air Conditioning Control Replacement .

Did you complete the replacement?

--

Go to Step 18

--

18

Operate the system in order to verify the repair.

Did you correct the condition?

--

System OK

Go to Step 2