The number below refers to the step number on the diagnostic table.
Step | Action | Value | Yes | No | ||||||
---|---|---|---|---|---|---|---|---|---|---|
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information | ||||||
2 | Press each button of the transmitter one at a time. Does the system operate normally? | -- | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 | ||||||
3 | Lock and unlock the door locks using the controls inside the vehicle. Do the locks operate properly? | -- | Go to Step 4 | Go to Power Door Locks Inoperative - All Doors and Switches in Doors | ||||||
4 | Operate the rear compartment lid release from the control inside the vehicle. Does the rear compartment lid release operate properly? | -- | Go to Step 5 | Go to Symptoms - Body Rear End in Body Rear End | ||||||
5 |
Important: Inspect that the keyless entry transmitter part number to determine that it is the correct model for the vehicle. A wrong model transmitter may pass this test, but will not activate the vehicle remote system.
Does a tone sound and the green light illuminate on the J 43241 after each button is pressed? | -- | Go to Step 10 | Go to Step 6 | ||||||
6 | Do any of the buttons on the transmitter sound the tone and illuminate the green light when pressed? | -- | Go to Step 9 | Go to Step 7 | ||||||
7 | Replace the transmitter battery. Refer to Transmitter Battery Replacement . Did you complete the replacement? | -- | Go to Step 8 | -- | ||||||
8 |
Does a tone sound and the green light illuminate on the J 43241 after each button is pressed? | -- | Go to Step 10 | Go to Step 9 | ||||||
9 | Replace the transmitter. Did you complete the replacement? | -- | Go to Step 10 | -- | ||||||
10 |
Important: All transmitters which are to be recognized by the remote control door lock receiver must be programmed in a single programming sequence. If the system is placed in program mode it will erase all previously programmed transmitters upon the receipt of the programming signal from the first transmitter. Perform the programming procedure. Refer to Transmitter Programming . Did you hear the body control module (BCM) chime to confirm that the transmitter programming has been completed? | -- | Go to Step 23 | Go to Step 11 | ||||||
11 |
Does the test lamp illuminate? | -- | Go to Step 12 | Go to Step 18 | ||||||
12 | Connect a test lamp between the battery positive voltage circuit of the RCDLR and the RCDLR ground circuit. Does the test lamp illuminate? | -- | Go to Step 13 | Go to Step 19 | ||||||
13 |
Does the DMM indicate the specified value? | B+ | Go to Step 14 | Go to Step 15 | ||||||
Does the test lamp illuminate? | -- | Go to Step 20 | Go to Step 16 | |||||||
15 | Test the keyless entry serial data circuit for the following:
Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 23 | Go to Step 17 | ||||||
16 | Inspect for poor connections at the harness connector of the RCDLR. Refer to Testing for Intermittent Conditions and Poor Connections and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 23 | Go to Step 21 | ||||||
17 | Repair the short to voltage in the keyless entry serial data circuit. Refer to Testing for a Short to Voltage and Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 23 | Go to Step 18 | ||||||
18 | Inspect for poor connections at the harness connector of the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 23 | Go to Step 22 | ||||||
19 | Repair the following in the battery positive voltage circuit of the RCDLR.
Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 23 | -- | ||||||
20 | Repair the open or high resistance in the RCDLR ground circuit. Refer to Testing for Continuity and Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 23 | -- | ||||||
21 |
Important: Perform the keyless entry transmitter programming procedure when replacing the RCDLR. Replace the RCDLR. Refer to Body Control Module (BCM) Programming/RPO Configuration in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 23 | -- | ||||||
22 | Replace the BCM. Refer to Body Control Module (BCM) Programming/RPO Configuration in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 23 | -- | ||||||
23 | Operate the system in order to verify the repair. Did you correct the condition? | -- | System OK | Go to Step 3 |