The camshaft position (CMP) actuator is attached to each camshaft and is hydraulically operated in order to change the angle of the camshaft relative to crankshaft position (CKP). The CMP actuator solenoid is controlled by the control module. The control module sends a pulse width modulated 12-volt signal to a CMP actuator solenoid. The solenoid controls the amount of engine oil flow to a CMP actuator. The CMP actuator can change the camshaft angle a maximum of 25 degrees. The control module increases the pulse width to accomplish the desired camshaft operation.

The engine is running.

The ECM detects an open, short to ground, or a short to voltage on the control circuit or an open on the ignition voltage circuit for more than 0.25 second.

DTCs P2088 and P2089 are Type B DTCs.

DTCs P2088 and P2089 are Type B DTCs.

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Electrical Information Reference

Scan Tool Reference

Control Module References for scan tool information

Important: The supply of clean pressurized engine oil to the CMP actuator is essential to CMP actuator performance.

1. Observe the engine oil level. The engine oil level should be within operating range. Refer to Approximate Fluid Capacities .
2. Ensure that the vehicle has the correct engine oil and is not old, burnt or contains additives. Refer to Checking Things Under the Hood in Service and Appearance Care within the Owner's Manual.

⇒	If the vehicle has the incorrect engine oil, is old, burnt, or contains additives, change the oil and filter.

3. Test the engine oil pressure for correct operation.
4. Allow the engine to reach operating temperature.
5. Set the parking brake and place the vehicle in Park for automatic, or Neutral for manual.
6. Observe the Int. CMP variance parameter. The Int. CMP Variance will rise for 1-2 seconds until the Int. CMP Angle parameter matches the Desired Int. CMP parameter. The Int. CMP Variance should again return to 0 degrees.

Important: The engine will run rough and may require throttle input to keep running.

7. Command the CMP actuator to 24 degrees. The Desired Int. CMP parameter should match the Int. CMP Angle parameter.
8. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

1. Ignition ON, measure for battery voltage between the CMP actuator solenoid ignition voltage and ground.

⇒	If less than battery voltage, test the CMP actuator solenoid ignition voltage circuit for an open, short to ground.

2. Connect a test lamp between the CMP actuator solenoid control circuit and a battery voltage. The test lamp should not illuminate.

⇒	If the test lamp illuminates, test the CMP actuator solenoid control circuit for a short to voltage. If the circuit tests normal, replace the control module.

3. Measure for 0 volts between the CMP actuator solenoid control and ground.

⇒	If voltage is present, test the control circuit for a short to voltage. If the circuit tests normal, replace the control module.

4. Command the CMP actuator solenoid ON. The test lamp should turn ON and OFF.

⇒	If the test lamp does not turn ON and OFF, test the CMP actuator solenoid ignition voltage circuit for high resistance. If the circuit tests normal, replace the control module.

5. If all circuits test normal, test or replace the CMP actuator solenoid.

1. Measure the resistance of each CMP actuator solenoid valve assembly. Resistance should be between 8-12 ohms.
2. Connect a jumper wire between the CMP actuator solenoid control circuit at the solenoid and a good ground. Connect a fused jumper wire to the CMP actuator solenoid ignition voltage circuit at the solenoid. Momentarily touch the fused jumper to B+. Observe the spool valve inside the CMP actuator. The spool valve should move from fully closed to fully opened position.

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

Control Module References for replacement, setup, and programming