GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC B3794 08: Cruise Control Function Request Circuit Signal Invalid

Diagnostic Fault Information

Circuit

Short to Ground

High Resistance

Open

Short to Voltage

Signal Performance

B+

1

B3794 08

1

1

B3794 08

Cruise Control Switch Signal

1

B3794 08

1

B3794 08

B3794 08

Ground

--

1

1

--

--

1. Cruise Control Malfunction

Circuit/System Description

The cruise control switch is an input to the body control module (BCM). The BCM monitors the cruise control Set/Coast and Resume/Accelerate switch signal circuit in order to detect when the driver has requested to perform a cruise control function. The BCM detects a specific voltage signal on the cruise control switch signal circuit when a switch is applied. The BCM sends a serial data message to the engine control module (ECM), indicating the status of the cruise control switches.

Conditions for Running the DTC

    • The ignition is ON.
    • The cruise switch is ON.

Conditions for Setting the DTC

    • The BCM detects an invalid voltage signal on the cruise control switch signal circuit.
    • The above condition is present for greater than 1 second.

Actions Taken When the DTC Sets

    • The malfunction indicator lamp (MIL) will not illuminate.
    • The cruise control system is disabled.

Conditions for Clearing the DTC

    • The condition responsible for setting the DTC no longer exists.
    • A history DTC will clear after 40 malfunction-free ignition cycles have occurred.

Reference Information

Schematic Reference

Cruise Control Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Cruise Control Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

Engine ON, observe the scan tool Cruise Control Switch parameter while pressing each of the cruise control switches. The parameter should toggle between On, Off, Resume and Set as the applicable switch is pressed.

Circuit/System Testing

  1. Ignition OFF, disconnect the harness connector at the steering wheel controls switch - left.
  2. Ignition OFF, test for less than 10 ohms between the ground circuit terminal 7 and ground.
  3. If greater than the specified value, test the ground circuit for an open/high resistance.
  4. Ignition ON, test for B+ between the B+ circuit terminal 4 and ground.
  5. If less than the specified value, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.
  6. Test for B+ between the B+ circuit terminal 4 and the signal circuit terminal 5.
  7. If less than the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM.
  8. Ignition OFF, disconnect the X2 harness connector at the BCM.
  9. Test for infinite resistance between the signal circuit terminal 5 and ground.
  10. If less than the specified value, test the signal circuit for a short to ground.
  11. If all circuits test normal, test or replace the steering wheel control switch - left.

Component Testing

  1. Disconnect the harness connector at the steering wheel controls switch - left.
  2. Cruise control switch ON, measure the resistance between terminal 4 and terminal 5 while individually activating and holding each cruise control function switch and compare the resistance reading to the values in the table below.
  3. If not within the specified resistance range, replace the steering wheel controls switch - left.

Function Switch

Minimum Resistance Value

Maximum Resistance Value

Off

O.L.

O.L.

On

0.0 Ohms

0.5 Ohms

- SET

1.4k Ohms

1.6k Ohms

+ RES

4.3k Ohms

4.5k Ohms

neutral position

8.0k Ohms

8.5k Ohms

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Steering Wheel Control Switch Assembly Replacement
    •  Control Module References for BCM replacement, setup, and programming