GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2009 🢒 Cobalt 🢒 HVAC 🢒 Heating, Ventilation, and Air Conditioning 🢒 Heater Core Cover Replacement

Removal Procedure
  1. Remove the body control module (BCM) from the vehicle. Refer to Body Control Module Replacement.

    2. Object Number: 877818 Size: SH
  2. Remove the front floor console left side extension panel. Refer to Front Floor Console Extension Replacement - Side.
  3. Pull back the carpet at the bottom of the left instrument panel (I/P) center support bracket and remove the left I/P center support bracket nuts.
  4. Remove the left I/P center support bracket.
  5. Remove the accelerator control pedal from the front of the dash and position out of the way. Refer to Accelerator Pedal with Position Sensor Assembly Replacement.

    6. Object Number: 873732 Size: SH
  6. Raise the center floor outlet duct while pushing the floor ducts down to disengage the ducts.
  7. Rotate the center floor outlet duct forward in the vehicle and pull down to disengage it from the HVAC module.

    8. Object Number: 1548653 Size: SH
  8. Remove the heater core cover heat stakes with a small chisel.
  9. Loosen the nut that is behind the fuel line bracket and remove the stud from the dash panel at the heater hoses.

    10. Object Number: 872600 Size: SH

    Note: Make certain that all of the heater core cover screws are removed before attempting to remove the heater core cover.

  10. Pull the heater core cover down just enough to clear the locating pins from the HVAC module. Slide the heater core cover rearward until the drain tube clears the front of dash. Slide the heater core cover down, rearward, and to the right to remove.

Installation Procedure

    Object Number: 872602 Size: SH
  1. Install a new drain tube seal onto the drain tube.

    2. Object Number: 872600 Size: SH

    Note: Spraying the heater core seal and the dashmat with a soap and water mixture will ease installation.

  2. Install the heater core cover from the right side. Slide up and forward into position. Align the drain tube with the hole in the front of dash. Raise the heater core cover into position while aligning holes with the locating pins from the HVAC module.
  3. Cut the sound insulator at the cowl near the center screw (1) approximately 76 mm (3 in) and fold the sound insulator back to ease in installation of the screw.

    4. Ensure the sound insulator is positioned back after the screws are tightened.

    Caution: Refer to Fastener Caution in the Preface section.


    Object Number: 1602968 Size: SH

    Note: Make certain that the heater core cover is properly positioned and is fully seated on the HVAC module before installing the screws. Be sure to install all heater core cover screws.

  4. Install the heater core cover screws and tighten to 1.8 N·m (15 lb in).
  5. Install the stud into the dash panel at the heater hoses and tighten the nut that is behind the fuel line bracket.

    6. Object Number: 877657 Size: SH
  6. Align the center floor duct with the HVAC module.
  7. Push the center floor duct up while rotating rearward in the vehicle to install on the HVAC module.
  8. Push down on the floor duct while rotating the center floor outlet ducts to align the ducts.
  9. Slide the center floor outlet duct down into position in the floor ducts.
  10. Install the accelerator control pedal. Refer to Accelerator Pedal with Position Sensor Assembly Replacement.

    11. Object Number: 877818 Size: SH
  11. Pull back the carpet and place the left center support bracket into position.
  12. Install the left center support bracket nuts and tighten to 10 N·m (89 lb in).
  13. Install the left side front floor console extension panel. Refer to Front Floor Console Extension Replacement - Side.
  14. Install the BCM to the vehicle. Refer to Body Control Module Replacement.