If a tire goes flat, avoid further tire and wheel damage by driving slowly to
a level place. Turn on your hazard warning flashers. See
Hazard Warning Flashers
for more information.
Caution: Changing a tire can be dangerous. The vehicle
can slip off the jack and roll over or fall on you or other people. You and they could
be badly injured or even killed. Find a level place to change your tire.
To help prevent the vehicle from moving:
- Set the parking brake firmly.
- Put an automatic transmission shift lever in PARK (P), or shift a manual
transmission to FIRST (1) or REVERSE (R).
- Turn off the engine and do not restart while the vehicle is raised.
- Do not allow passengers to remain in the vehicle.
Put the wheel blocks at the front and rear of the tire farthest away
from the one being changed. That would be the tire on the other side, at the opposite
end of the vehicle.
The following steps will tell you how to use the jack and change a tire.
Removing the Spare Tire and Tools
Crew Cab
Regular and Extended Cab
The tools you will need are under the passenger's seat. For crew cab models,
the jack and wheel blocks are under the driver's side rear seat. For regular and extended
cab vehicles the jack and wheel blocks are located under the cover at the center of
the vehicle behind the front seats.
- The vehicle will have a cover if it is an extended or regular cab.
- Move the seats forward and turn the wing nut on the cover counterclockwise
to remove it. For crew cab models, reach under the rear seat to access the jack and
wheel blocks. To reinstall the jack and wheel block assembly in the mounting bracket,
insert the tabs into the jack base by pushing the blocks up into the assembly. The
outer hole in the jack base aligns with the tab on the bracket. When reinstalling,
make sure the jack is secure, but do not overtighten the jack in the bracket.
- The wheel blocks and the wheel block retainer can be removed by turning
the wing nut counterclockwise.
Put the wheel blocks at the front and
rear of the tire farthest away from the one being changed. That would be the tire
on the other side, at the opposite end of the vehicle.
- There is also a wing nut used to retain the storage bag and tools located
under the front passenger's seat. To remove it, turn the wing nut counterclockwise.
You will use the jack handle extensions and the wheel wrench to remove the underbody-mounted
spare tire.
-
Jack Handle Extensions
Bottle Jack
Extension Tool
Wheel Wrench
Wheel Blocks
- Assemble the wheel wrench (D) and the jack handle extensions (A)
as shown.
- Insert
the hoist end (chiseled end) of the extension tool through the hole in the
rear bumper and into the funnel-shaped guide. The chiseled end of the extension is
used to lower the spare tire.
- Turn the wheel wrench (D) counterclockwise to lower the spare tire
to the ground. Continue to turn the wheel wrench until the spare tire can be pulled
out from under the vehicle.
If the spare tire does not lower to the ground,
the secondary latch is engaged causing the tire not to lower. See "Secondary
Latch System" later in this section.
- When the tire has been lowered, tilt the
retainer and slide it up the cable so it can be pulled up through the wheel opening.
- Put the spare tire near the flat tire.
Removing the Flat Tire and Installing the Spare Tire
Use the following pictures and instructions to remove the flat tire and raise
the vehicle.
The tools you will be using include the bottle jack (A), the wheel blocks (B),
the extension tool (C), the jack handle extensions (D), and the wheel
wrench (E).
- Remove the center cap by placing the chisel
end of the wheel wrench (E) in the slot on the wheel and gently prying the cap out.
- Use the wheel wrench to loosen all the wheel
nuts. Turn the wheel wrench counterclockwise to loosen the wheel nuts. Do not remove
the wheel nuts yet.
Front Location
Front Location
Rear Location
- Position the jack (A) under the vehicle as shown.
Front Location
- If the flat tire is on the front of the vehicle, position the jack to the rear
of the front tire in the pocket off of the frame.
If the flat tire is on the rear, position the jack under the rear axle and get
as close as possible to the shock absorber.
Caution: Getting under a vehicle when it is jacked up is dangerous. If the vehicle
slips off the jack you could be badly injured or killed. Never get under a
vehicle when it is supported only by a jack.
Caution: Raising your vehicle with the jack improperly positioned can damage
the vehicle and even make the vehicle fall. To help avoid personal injury
and vehicle damage, be sure to fit the jack lift head into the proper location
before raising the vehicle.
Rear Position
- Make sure the jack head is positioned so that the rear axle is resting securely
between the grooves that are on the jack head.
- Turn the wheel wrench clockwise to raise the vehicle. Raise the vehicle
far enough off the ground so there is enough room for the spare tire to fit under
the wheel well.
- Remove all the wheel nuts and take off the
flat tire.
- Remove any rust or dirt from the wheel bolts,
mounting surfaces and spare wheel.
Caution: Rust or dirt
on a wheel or other parts to which it is fastened, can make the wheel nuts become
loose and eventually the wheel could come off and cause a crash. Always remove all
rust and dirt from wheels and other parts.
Caution: Never use oil or grease on bolts or nuts because
the nuts might come loose. The vehicle's wheel could fall off, causing a crash.
- After mounting the spare, put the wheel
nuts back on with the rounded end of the nuts toward the wheel. Tighten each wheel
nut by hand. Then use the wheel wrench to tighten the nuts until the wheel is held
against the hub.
Front Position
Rear Position
- Turn the wheel wrench counterclockwise to lower the vehicle. Lower the jack
completely.
- Tighten the wheel nuts firmly in a crisscross
sequence as shown by turning the wheel wrench clockwise.
Caution: Wheel nuts
that are improperly or incorrectly tightened can cause the wheels to become loose
or come off. The wheel nuts should be tightened with a torque wrench to the proper
torque specification after replacing. Follow the torque specification supplied by
the aftermarket manufacturer when using accessory locking wheel nuts. See
Capacities and Specifications for original equipment
wheel nut torque specifications.
Notice: Improperly
tightened wheel nuts can lead to brake pulsation and rotor damage. To avoid expensive
brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper
torque specification. See
Capacities and Specifications
for
the wheel nut torque specification.
When you reinstall the regular wheel and tire, you must also reinstall the center
cap. Place the cap on the wheel and tap it into place until it seats flush with the
wheel. The cap only goes on one way. Be sure to line up the tab on the center cap
with the indentation on the wheel.
Storing a Flat or Spare Tire, Jack and Tools
Caution: Storing a jack, a tire, or other equipment in the passenger compartment
of the vehicle could cause injury. In a sudden stop or collision, loose equipment
could strike someone. Store all these in the proper place.
Notice: Storing an aluminum wheel with a flat tire under
your vehicle for an extended period of time or with the valve stem pointing up can
damage the wheel. Always stow the wheel with the valve stem pointing down and have
the wheel/tire repaired as soon as possible.
Store the tire under the rear of the vehicle in the spare tire carrier. Use
the art and text following to help you.
- Put the tire on the ground at the rear of the vehicle with the valve stem
pointed down.
- Tilt the retainer downward and through the
wheel opening. Make sure the retainer is fully seated across the underside of the
wheel.
- Attach
the wheel wrench and extensions together.
- Insert
the hoist end through the hole in the rear bumper and into the funnel-shaped guide.
- Turn the wheel wrench clockwise to raise the tire part way up. Make sure
the retainer is seated in the wheel opening and the valve stem is pointed down.
- Raise the tire fully against the underside of the vehicle by turning the
wheel wrench clockwise until you feel it skip twice. You cannot overtighten the cable.
Push and Pull on Tire
Turn Tire
- Make sure the tire is stored securely. Push, pull, and then try to turn
the tire. If the tire moves, check to make sure the tire valve stem is pointing down,
then use the wheel wrench to loosen and then tighten the cable.
Return the wheel wrench and jack extensions and the storage bag to the location
under the front passenger's seat. Reinstall the jack and wheel blocks, be sure to
install the wheel blocks first. Secure the items in the vehicle as shown.
Crew Cab
Bottle Jack
Wheel Blocks
Wing Nut
Regular and Extended Cab
Bottle Jack
Wheel Blocks
Wing Nut
Secondary Latch System
Your vehicle has an underbody mounted tire hoist assembly equipped with a secondary
latch system. It is designed to stop the spare tire from suddenly falling off your
vehicle. For the secondary latch to work, the spare must be installed with the valve
stem pointing down. See "Storing a Flat or Spare Tire, Jack and Tools"
earlier in this section.
Caution: Before beginning
this procedure read all the instructions. Failure to read and follow the instructions
could damage the hoist assembly and you and others could get hurt. Read and follow
the instructions listed next.
To release the spare tire from the secondary latch do the following:
- Check under the vehicle to see if the cable
end fitting is visible.
- If the cable end fitting is not visible proceed to Step 6.
If it is visible, first try to tighten the cable by turning the wheel wrench
clockwise until you hear two clicks or feel it skip twice. You cannot overtighten
the cable.
- Loosen the cable by turning the wheel wrench counterclockwise three or
four turns.
- Repeat this procedure at least two times. If the spare tire lowers to
the ground, continue with Step 5 of "Removing the Spare Tire and Tools"
earlier in this section.
- Turn the wrench counterclockwise until approximately six inches
(15 cm) of cable is exposed.
- Stand the wheel blocks on their shortest ends, with the backs facing each other.
- Place the bottom edge of the jack on the wheel blocks, separating them
so that the jack is balanced securely.
- Attach the jack handle, extension, and wheel wrench to the jack and place it
(with the wheel blocks) under the vehicle towards the front of the rear bumper. Position
the center lift point of the jack under the wheel.
- Turn the wrench clockwise to raise the jack until it lifts the tire.
- Continue raising the jack until the tire stops moving upward and is held
firmly in place. The secondary latch has released and the tire is balancing on the
jack.
- Remove
the jack handle and insert the hoist end of the extension through the hole in the
rear bumper.
Turn the wheel counterclockwise one turn or until the wheel
retainer assembly falls out.
- Reinsert the jack handle into the jack. Lower the jack by turning the
wheel wrench counterclockwise. Keep lowering the jack until the spare tire slides
off the jack or is hanging by the cable.
Caution: Someone standing
too close during the procedure could be injured by the jack. If the spare tire does
not slide off the jack completely, make sure no one is behind you or on either side
of you as you pull the jack out from under the spare.
- Disconnect the jack handle from the jack and carefully remove the jack. Use
one hand to push against the spare while firmly pulling the jack out from under the
spare tire with the other hand.
If the spare tire is hanging from the
cable, insert the hoist handle, extension and wheel wrench into the hoist shaft hole
in the bumper and turn the wheel wrench counterclockwise to lower the spare the rest
of the way.
- Tilt the tire retainer at the end of the
cable and pull it through the wheel opening. Pull the tire out from under the vehicle.
- If the cable is hanging under the vehicle, turn the wheel wrench clockwise
to raise the cable back up.
Have the hoist assembly inspected as soon as you can. You will not be able to
store a spare or flat tire using the hoist assembly until it has been replaced.
To continue changing the flat tire, see "Removing the Flat Tire and Installing
the Spare Tire" earlier in this section.