Circuit Description
The manifold absolute pressure (MAP) sensor measures the pressure inside the intake manifold. Pressure in the intake manifold is affected by engine speed, throttle opening, air temperature, and barometric pressure (BARO). A diaphragm within the MAP sensor is displaced by the pressure changes that occur from the varying load and operating conditions of the engine. The sensor translates this action into electrical resistance. The MAP sensor wiring includes 3 circuits. The powertrain control module (PCM) supplies a regulated 5 volts to the sensor on a 5-volt reference circuit. The PCM supplies a ground on a low reference circuit. The MAP sensor provides a signal voltage to the PCM, relative to the pressure changes on the MAP sensor signal circuit. The PCM converts the signal voltage input to a pressure value.
Under normal operation, the highest pressure that can exist in the intake manifold is equal to the BARO. This occurs when the vehicle is operated at wide open throttle (WOT), or when the ignition is ON while the engine is OFF. Under these conditions, the PCM uses the MAP sensor to determine the current BARO. The lowest manifold pressures occur when the vehicle is idling or decelerating. The MAP can range from 10 kPa when pressures are low to as much as 104 kPa when pressures are high, depending on the BARO.
Within the PCM, the intake flow rationality diagnostic has the ability to determine an inaccurate input from the 3 systems it monitors. Calibrated within the diagnostic are estimates for the MAP, the mass air flow (MAF), and the throttle position (TP) for all engine operating conditions. The diagnostic compares the estimated values to the actual sensor inputs. If the PCM detects that the MAP sensor input is not within a calibrated limit of the estimated value, DTC P0106 sets.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0106 Manifold Absolute Pressure (MAP) Sensor Performance
Conditions for Running the DTC
| • | DTCs P0102, P0103, P0107, P0108, P0112, P0113, P0117, P0118, P0335, P0336 are not set. |
| • | The engine speed is between 400-6,400 RPM. |
| • | The engine coolant temperature (ECT) is between 70-125°C (158-257°F). |
| • | The intake air temperature (IAT) is between -7 to +125°C (+19 to +257°F). |
| • | DTC P0106 runs continuously once the above conditions are met. |
Conditions for Setting the DTC
The PCM detects that the MAP sensor pressure is not within the calibrated limit of the estimated value for more than 1 second.
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step tests the ability of the MAP sensor to correctly indicate BARO.
-
The measurement noted in this step will be used in subsequent steps if the measurement does not exceed the specified value.
-
This step calculates the resistance in the 5-volt reference circuit.
-
This step calculates the resistance in the low reference circuit.
Step | Action | Values | Yes | No | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Engine Controls Connector End Views or Powertrain Control Module Connector End Views | ||||||||||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information | ||||||||
2 | Inspect for the following conditions:
Did you find and correct the condition? | -- | Go to Step 25 | Go to Step 3 | ||||||||
3 |
Important: The vehicle used for the comparison is not limited to the same type of vehicle as is being serviced. A vehicle known to provide an accurate reading is acceptable. Do you have access to another vehicle in which the MAP sensor pressure can be observed with a scan tool? | -- | Go to Step 4 | Go to Step 5 | ||||||||
Is the difference between the values less than the specified value? | 3 kPa | Go to Step 6 | Go to Step 11 | |||||||||
5 |
Important: The Altitude vs. Barometric Pressure table indicates a pressure range for a given altitude under normal weather conditions. Weather conditions consisting of very low or very high pressure and/or very low or very high temperature may cause a reading to be slightly out of range.
Does the MAP sensor indicate the correct barometric pressure? | -- | Go to Step 6 | Go to Step 11 | ||||||||
6 |
Does the MAP sensor pressure change? | -- | Go to Step 7 | Go to Step 11 | ||||||||
7 |
Is the decrease in MAP sensor pressure consistent? | -- | Go to Step 8 | Go to Step 11 | ||||||||
8 | Apply vacuum with the J 23738-A until 20 inches Hg is reached. Is the MAP sensor pressure less than the specified value? | 34 kPa | Go to Step 9 | Go to Step 11 | ||||||||
9 | Disconnect the J 23738-A from the MAP sensor. Does the MAP sensor pressure return to the value observed in step 4 or 5? | -- | Go to Step 10 | Go to Step 23 | ||||||||
10 | Inspect for the following conditions:
Did you find and correct the condition? | -- | Go to Step 25 | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | ||||||||
11 | Test for an intermittent and for a poor connection at the MAP sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 25 | Go to Step 12 | ||||||||
Is the pressure less than the specified value? | 12 kPa | Go to Step 13 | Go to Step 17 | |||||||||
13 | Measure the voltage from the 5-volt reference circuit of the MAP sensor to a good ground with a DMM. Refer to Circuit Testing in Wiring Systems. Note the measurement as Supply Voltage. Is the voltage more than the specified value? | 5.2 V | Go to Step 18 | Go to Step 14 | ||||||||
Is the amperage equal to the specified value? | 0 mA | Go to Step 20 | Go to Step 15 | |||||||||
Important: Before any calculations are performed, ensure that all measurements are converted into like units, for example volts/amps or millivolts/milliamps. Is the result more than the specified value? | 5 ohms | Go to Step 19 | Go to Step 16 | |||||||||
16 |
Important: Before any calculations are performed, ensure that all measurements are converted into like units, for example volts/amps or millivolts/milliamps. Is the result more than the specified value? | 5 ohms | Go to Step 21 | Go to Step 23 | ||||||||
17 | Test the MAP sensor signal circuit between the powertrain control module (PCM) and the MAP sensor for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 25 | Go to Step 22 | ||||||||
18 | Test all branches of the 5-volt reference circuit that is shared with the MAP sensor for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 25 | Go to Step 22 | ||||||||
19 | Test the 5-volt reference circuit between the PCM and the MAP sensor for high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 25 | Go to Step 22 | ||||||||
20 | Test the low reference circuit between the PCM and the MAP sensor for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 25 | Go to Step 22 | ||||||||
21 | Test the low reference circuit between the PCM and the MAP sensor for high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 25 | Go to Step 22 | ||||||||
22 | Test for shorted terminals and for poor connections at the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 25 | Go to Step 24 | ||||||||
23 | Replace the MAP sensor. Refer to Manifold Absolute Pressure Sensor Replacement . Did you complete the replacement? | -- | Go to Step 25 | -- | ||||||||
24 | Replace the PCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 25 | -- | ||||||||
25 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 26 | ||||||||
26 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information | System OK | ||||||||
