GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2006 🢒 Colorado Pickup - 2WD 🢒 Transmission/Transaxle 🢒 Manual Transmission - Aisin AR5 🢒 Transmission Disassemble

Transmission Disassemble Colorado

Tools Required

J 8433 Two Jaw Puller


    Object Number: 872959 Size: SH

    Important: The following steps apply to both the 4WD and the RWD transmission, except where noted.

  1. Remove the drain plug, with aluminum washer, and drain the transmission fluid.

    2. Object Number: 880951 Size: SH
  2. If RWD, remove the vehicle speed sensor with O-ring seal.

    3. Object Number: 880943 Size: SH
  3. Remove the backup lamp switch, with the aluminum washer, from the front case.

    4. Object Number: 880652 Size: SH
  4. Remove the 9 bolts retaining the clutch housing.
  5. Using a soft-face hammer, remove the clutch housing from the transmission assembly.

    6. Object Number: 880655 Size: SH
  6. Shift the transmission into NEUTRAL.
  7. Remove the shift control housing bolts.
  8. Remove the shift control housing.
  9. Remove the shift control housing gasket.

    10. Object Number: 1526781 Size: SH
  10. Remove the shift control lever socket bolt.

    11. Object Number: 872969 Size: SH
  11. Mark the location of the brackets and the studs.
  12. Remove the extension housing retaining bolts, studs, and brackets.

    13. The 4WD does not use a bracket on the left side of the transmission.

    Notice: Refer to Machined Surface Damage Notice in the Preface section.


    Object Number: 1526783 Size: SH
  13. Using a soft-face hammer, separate the extension housing from the intermediate case.
  14. Slide the extension housing off the shift control shaft.
  15. Remove the shift control socket from the extension housing shift lever cavity.

    16. Object Number: 880657 Size: SH
  16. Remove the shift control shaft from the shift shaft gates.

    17. Object Number: 872978 Size: SH
  17. Remove the front bearing retainer bolts. Discard the bolts. New bolts are required for assembly.
  18. Remove the front bearing retainer.

    19. Object Number: 872983 Size: SH
  19. Using a suitable punch and a hammer, remove the input shaft seal from the bearing retainer. Do not use the seal again.

    20. Object Number: 872989 Size: SH
  20. Remove the outer retaining ring from the input shaft bearing.
  21. Remove the outer retaining ring from the countershaft front bearing.

    22. Notice: Refer to Machined Surface Damage Notice in the Preface section.


    Object Number: 880658 Size: SH
  22. Using a soft-face hammer on the transmission front case, shear the sealer.
  23. Remove the transmission front case from the intermediate case.

    24. Object Number: 880662 Size: SH
  24. Remove the oil baffle bolts.
  25. Remove the oil baffle.

    26. Object Number: 880663 Size: SH
  26. Remove the magnet.

    27. Notice: Refer to Machined Surface Damage Notice in the Preface section.


    Object Number: 880665 Size: SH
  27. Install 2 bolts, with nuts, in the lower holes of the intermediate case. The bolts will be used to hold the intermediate case in a vise during disassembly and assembly.

    28. Object Number: 881213 Size: SH

    Important: Before removal of the 5th synchronizer gear, measure the axial play of the speed gear. Incorrect axial play of the gear may cause shifting concerns or transmission noise.

  28. Using a feeler gage between the 5th countershaft gear and the thrust washer, measure the axial clearance.

    29. Specification

        • Standard Clearance: 0.10-0.35 mm (0.0039-0.0138 in)
        • Maximum Clearance: 0.40 mm (0.0157 in)
  29. If the clearance exceeds the maximum, refer to Gears and Shafts Cleaning and Inspection .

    30. Object Number: 880666 Size: SH
  30. Mount the intermediate case assembly in a vise on the 2 previously installed bolts.
  31. Using 2 screwdrivers and a hammer, remove the 5th synchronizer gear retaining ring.

    32. Object Number: 880668 Size: SH
  32. Using J 8433 with 2 bolts in the threaded holes of the 5th synchronizer gear, remove the gear.

    33. Object Number: 1526787 Size: SH
  33. Remove the 5th/reverse gear synchronizer.

    34. Object Number: 1526791 Size: SH
  34. Using a hammer and a punch, remove the 5th shift fork roll pin.

    35. Object Number: 1526793 Size: SH
  35. Remove the shift fork, the 5th/reverse synchronizer sleeve and blocking ring assembly and the 5th countershaft gear and bearing.

    36. Object Number: 880678 Size: SH
  36. Remove the 5th countershaft gear thrust washer.
  37. Remove the thrust washer lock pin.

    38. Object Number: 880680 Size: SH
  38. Remove the bolts for the rear bearing retainer.
  39. Remove the rear bearing retainer.

    40. Object Number: 880682 Size: SH
  40. Using a soft-face hammer, tap the countershaft rearward to expose the outer retaining ring on the countershaft rear bearing.
  41. Using a suitable prying tool on the retaining ring, remove the countershaft rear bearing. The bearing will slide out of the case if the countershaft is kept in position with the output shaft.

    42. Object Number: 880684 Size: SH
  42. Remove the countershaft.

    43. Object Number: 880685 Size: SH
  43. Remove the reverse idler gear shaft and reverse idler gear.

    44. Object Number: 880686 Size: SH
  44. Remove the input shaft assembly, with the 4th gear blocking ring, and output shaft front support bearing from the output shaft.

    45. Object Number: 880688 Size: SH
  45. Remove the 1st/2nd shift fork bolt.
  46. Remove the 3rd/4th shift fork bolt.

    47. Object Number: 880690 Size: SH
  47. Remove the retaining ring for the reverse shift lever on the reverse shift shaft.
    48. • Use a suitable pair of pliers to push the retaining ring.
    • Only push the retaining ring partially off to keep it from flying.
    • Use a pair of pliers to remove the retaining ring the rest of the way.

    Object Number: 880691 Size: SH
  48. Shift the reverse shift shaft forward.
  49. Move the reverse shift lever forward past the retaining ring groove on the reverse shift shaft. This allows clearance of the reverse shift fork during removal of the output shaft.

    50. Object Number: 880695 Size: SH
  50. Remove the output shaft rear bearing outer retaining ring.

    51. Object Number: 880697 Size: SH
  51. Remove the output shaft assembly.
    52. • Hold the 1st/2nd shift fork and the 3rd/4th shift fork in position to the output shaft.
    • Slide the 1st/2nd shift fork and the 3rd/4th shift fork off the shift shafts while removing the output shaft.

    Object Number: 880698 Size: SH

    Important: If the shift shafts or the intermediate case do not require service, proceed to Output Shaft Disassemble. If the shift shafts or intermediate case require service, proceed to the next step.

  52. Remove the 4 shift shaft detent plugs for the shift detent balls and springs. Discard the plugs. New plugs are required for assembly.

    53. Object Number: 880699 Size: SH
  53. Using a magnet, remove the 1st/2nd shift shaft detent spring and ball.
  54. Using a magnet, remove the 3rd/4th shift shaft detent spring and ball.
  55. Using a magnet, remove the 5th shift shaft detent spring and ball. The reverse shift shaft does not have a detent spring and ball in the plug opening.

    56. Object Number: 880707 Size: SH

    Important: To prevent the retaining rings from flying, cover the area with a rag.

  56. Remove the following shift shaft retaining rings:
    57. • The 1st/2nd shift shaft
    • The 3rd/4th shift shaft
    • The 5th shift shaft
       - Use a suitable pair of pliers to push the retaining ring.
       - Only push the retaining ring partially off to keep it from flying.
       - Use a pair of pliers to remove the retaining ring the rest of the way.

    Object Number: 880763 Size: SH
  57. Remove the 3rd/4th shift shaft.

    58. Object Number: 880771 Size: SH
  58. Using a magnet, remove the 1st/2nd and 3rd/4th shift shaft interlock pin.
  59. Remove the 1st/2nd shift shaft.
  60. Remove the small interlock pin from the 1st/2nd shift shaft.

    61. Object Number: 880775 Size: SH
  61. Using a magnet, remove the 5th shift shaft and 1st/2nd shift shaft interlock pin.
  62. Remove the 5th shift shaft.

    63. Object Number: 880784 Size: SH
  63. Remove the detent ball from the reverse shift lever.

    64. Object Number: 880787 Size: SH
  64. Remove the reverse shift lever, with the reverse shift fork, from the reverse shift shaft.
    65. 64.1. Slide the shift lever to the end of the shaft.
    64.2. Cover the detent ball opening with your hand.
    64.3. Let the detent ball and spring land in your hand.

    Object Number: 880791 Size: SH
  65. Using a magnet, remove the interlock pin from the reverse shift shaft. The shaft may require moving back and forth to remove the interlock pin.
  66. Remove the reverse shift shaft.

    67. Object Number: 880792 Size: SH
  67. Remove the bolts and the reverse shift fork bracket.

Transmission Disassemble Solstice

Tools Required

J 8433 Two Jaw Puller


    Object Number: 872959 Size: SH
  1. Remove the drain plug, with aluminum washer, and drain the transmission fluid.

    2. Object Number: 1644159 Size: SH
  2. Remove the vehicle speed sensor with O-ring seal.

    3. Object Number: 1644162 Size: SH
  3. Remove the backup lamp switch, with the aluminum washer, from the front case.

    4. Object Number: 1644163 Size: SH
  4. Remove the 9 bolts retaining the clutch housing.
  5. Using a soft-face hammer, remove the clutch housing from the transmission assembly.

    6. Object Number: 1847538 Size: SH
  6. Remove the output shaft nut.
  7. Remove the o-ring seal.
  8. Remove the output flange.
  9. Remove the output flange dirt deflector.

    10. Object Number: 1644181 Size: SH
  10. Remove the shift control lever boot.
  11. Remove the shift control lever bolt/screw and retainer.
  12. Remove the shift control bracket screws and shift control bracket.

    13. Object Number: 1644165 Size: SH
  13. Shift the transmission into NEUTRAL.
  14. Remove the shift control housing bolts.
  15. Remove the shift control housing.
  16. Remove the shift control housing gasket.

    17. Object Number: 1644169 Size: SH
  17. Remove the shift control lever socket bolt.

    18. Object Number: 1644170 Size: SH
  18. Mark the location of the brackets and the studs.
  19. Remove the extension housing retaining bolts, studs, and brackets.

    20. Notice: Refer to Machined Surface Damage Notice in the Preface section.


    Object Number: 1644171 Size: SH
  20. Using a soft-face hammer, separate the extension housing from the intermediate case.
  21. Slide the extension housing off the shift control shaft.
  22. Remove the shift control socket from the extension housing shift lever cavity.

    23. Object Number: 880657 Size: SH
  23. Remove the shift control shaft from the shift shaft gates.

    24. Object Number: 872978 Size: SH
  24. Remove the front bearing retainer bolts. Discard the bolts. New bolts are required for assembly.
  25. Remove the front bearing retainer.

    26. Object Number: 872983 Size: SH
  26. Using a suitable punch and a hammer, remove the input shaft seal from the bearing retainer. Do not use the seal again.

    27. Object Number: 872989 Size: SH
  27. Remove the outer retaining ring from the input shaft bearing.
  28. Remove the outer retaining ring from the countershaft front bearing.

    29. Notice: Refer to Machined Surface Damage Notice in the Preface section.


    Object Number: 880658 Size: SH
  29. Using a soft-face hammer on the transmission front case, shear the sealer.
  30. Remove the transmission front case from the intermediate case.

    31. Object Number: 880662 Size: SH
  31. Remove the oil baffle bolts.
  32. Remove the oil baffle.

    33. Object Number: 880663 Size: SH
  33. Remove the magnet.

    34. Notice: Refer to Machined Surface Damage Notice in the Preface section.


    Object Number: 880665 Size: SH
  34. Install 2 bolts, with nuts, in the lower holes of the intermediate case. The bolts will be used to hold the intermediate case in a vise during disassembly and assembly.

    35. Object Number: 881213 Size: SH

    Important: Before removal of the 5th synchronizer gear, measure the axial play of the speed gear. Incorrect axial play of the gear may cause shifting concerns or transmission noise.

  35. Using a feeler gage between the 5th countershaft gear and the thrust washer, measure the axial clearance.

    36. Specification

        • Standard Clearance: 0.10-0.35 mm (0.0039-0.0138 in)
        • Maximum Clearance: 0.40 mm (0.0157 in)
  36. If the clearance exceeds the maximum, refer to Gears and Shafts Cleaning and Inspection .

    37. Object Number: 880666 Size: SH
  37. Mount the intermediate case assembly in a vise on the 2 previously installed bolts.
  38. Using 2 screwdrivers and a hammer, remove the 5th synchronizer gear retaining ring.

    39. Object Number: 880668 Size: SH
  39. Using J 8433 with 2 bolts in the threaded holes of the 5th synchronizer gear, remove the gear.

    40. Object Number: 1526787 Size: SH
  40. Remove the 5th/reverse gear synchronizer.

    41. Object Number: 1526791 Size: SH
  41. Using a hammer and a punch, remove the 5th shift fork roll pin.

    42. Object Number: 1526793 Size: SH
  42. Remove the shift fork, the 5th/reverse synchronizer sleeve and blocking ring assembly and the 5th countershaft gear and bearing.

    43. Object Number: 880678 Size: SH
  43. Remove the 5th countershaft gear thrust washer.
  44. Remove the thrust washer lock pin.

    45. Object Number: 880680 Size: SH
  45. Remove the bolts for the rear bearing retainer.
  46. Remove the rear bearing retainer.

    47. Object Number: 880682 Size: SH
  47. Using a soft-face hammer, tap the countershaft rearward to expose the outer retaining ring on the countershaft rear bearing.
  48. Using a suitable prying tool on the retaining ring, remove the countershaft rear bearing. The bearing will slide out of the case if the countershaft is kept in position with the output shaft.

    49. Object Number: 880684 Size: SH
  49. Remove the countershaft.

    50. Object Number: 880685 Size: SH
  50. Remove the reverse idler gear shaft and reverse idler gear.

    51. Object Number: 880686 Size: SH
  51. Remove the input shaft assembly, with the 4th gear blocking ring, and output shaft front support bearing from the output shaft.

    52. Object Number: 880688 Size: SH
  52. Remove the 1st/2nd shift fork bolt.
  53. Remove the 3rd/4th shift fork bolt.

    54. Object Number: 880690 Size: SH
  54. Remove the retaining ring for the reverse shift lever on the reverse shift shaft.
    55. • Use a suitable pair of pliers to push the retaining ring.
    • Only push the retaining ring partially off to keep it from flying.
    • Use a pair of pliers to remove the retaining ring the rest of the way.

    Object Number: 880691 Size: SH
  55. Shift the reverse shift shaft forward.
  56. Move the reverse shift lever forward past the retaining ring groove on the reverse shift shaft. This allows clearance of the reverse shift fork during removal of the output shaft.

    57. Object Number: 880695 Size: SH
  57. Remove the output shaft rear bearing outer retaining ring.

    58. Object Number: 880697 Size: SH
  58. Remove the output shaft assembly.
    59. • Hold the 1st/2nd shift fork and the 3rd/4th shift fork in position to the output shaft.
    • Slide the 1st/2nd shift fork and the 3rd/4th shift fork off the shift shafts while removing the output shaft.

    Object Number: 880698 Size: SH

    Important: If the shift shafts or the intermediate case do not require service, proceed to Output Shaft Disassemble. If the shift shafts or intermediate case require service, proceed to the next step.

  59. Remove the 4 shift shaft detent plugs for the shift detent balls and springs. Discard the plugs. New plugs are required for assembly.

    60. Object Number: 880699 Size: SH
  60. Using a magnet, remove the 1st/2nd shift shaft detent spring and ball.
  61. Using a magnet, remove the 3rd/4th shift shaft detent spring and ball.
  62. Using a magnet, remove the 5th shift shaft detent spring and ball. The reverse shift shaft does not have a detent spring and ball in the plug opening.

    63. Object Number: 880707 Size: SH

    Important: To prevent the retaining rings from flying, cover the area with a rag.

  63. Remove the following shift shaft retaining rings:
    64. • The 1st/2nd shift shaft
    • The 3rd/4th shift shaft
    • The 5th shift shaft
       - Use a suitable pair of pliers to push the retaining ring.
       - Only push the retaining ring partially off to keep it from flying.
       - Use a pair of pliers to remove the retaining ring the rest of the way.

    Object Number: 880763 Size: SH
  64. Remove the 3rd/4th shift shaft.

    65. Object Number: 880771 Size: SH
  65. Using a magnet, remove the 1st/2nd and 3rd/4th shift shaft interlock pin.
  66. Remove the 1st/2nd shift shaft.
  67. Remove the small interlock pin from the 1st/2nd shift shaft.

    68. Object Number: 880775 Size: SH
  68. Using a magnet, remove the 5th shift shaft and 1st/2nd shift shaft interlock pin.
  69. Remove the 5th shift shaft.

    70. Object Number: 880784 Size: SH
  70. Remove the detent ball from the reverse shift lever.

    71. Object Number: 880787 Size: SH
  71. Remove the reverse shift lever, with the reverse shift fork, from the reverse shift shaft.
    72. 71.1. Slide the shift lever to the end of the shaft.
    71.2. Cover the detent ball opening with your hand.
    71.3. Let the detent ball and spring land in your hand.

    Object Number: 880791 Size: SH
  72. Using a magnet, remove the interlock pin from the reverse shift shaft. The shaft may require moving back and forth to remove the interlock pin.
  73. Remove the reverse shift shaft.

    74. Object Number: 880792 Size: SH
  74. Remove the bolts and the reverse shift fork bracket.