GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2007 🢒 Colorado Pickup - 2WD 🢒 Engine 🢒 Engine Controls and Fuel - 2.9L 🢒 DTC P1107

Circuit Description

The manifold absolute pressure (MAP) sensor measures the pressure inside the intake manifold. Pressure in the intake manifold is affected by engine speed, throttle opening, air temperature, and barometric pressure (BARO). A diaphragm within the MAP sensor is displaced by the pressure changes that occur from the varying load and operating conditions of the engine. The sensor translates this action into electrical resistance. The MAP sensor wiring includes 3 circuits. The powertrain control module (PCM) supplies a regulated 5 volts to the sensor on a 5-volt reference circuit. The PCM supplies a ground on a low reference circuit. The MAP sensor provides a signal voltage to the PCM, relative to the pressure changes, on the MAP sensor signal circuit. The PCM converts the signal voltage input to a pressure value.

Under normal operation the highest pressure that can exist in the intake manifold is equal to BARO. This occurs when the vehicle is operated at wide-open throttle (WOT) or when the ignition is on while the engine is off. Under these conditions, the PCM uses the MAP sensor to determine the current BARO. The lowest manifold pressures occur when the vehicle is idling or decelerating. MAP can range from 10 kPa, when pressures are low, to as much as 104 kPa when pressures are high, depending on the BARO. The PCM monitors the MAP sensor signal for pressure outside of the normal range. If the PCM detects that the MAP sensor pressure is intermittently low, DTC P1107 sets.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P1107 Manifold Absolute Pressure (MAP) Sensor Circuit Intermittent Low Voltage

Conditions for Running the DTC
    • DTCs P0068, P0120, P0121, P0220, P0641, P0651, P1516, P1680, P1681, P2101, P2120, P2125, P2135, P2138, P2176 are not set.
    • The PCM is in run state.
    • The throttle angle is more than 0 percent when the engine speed is less than 1,100 RPM.
        OR
    • The throttle angle is more than 9 percent when the engine speed is more than 1,100 RPM.

Conditions for Setting the DTC

The PCM detects that the MAP sensor pressure is intermittently less than 12 kPa for more than 10 seconds.

Action Taken When the DTC Sets
    • The control module stores the DTC information into memory when the diagnostic runs and fails.
    • The malfunction indicator lamp (MIL) will not illuminate.
    • The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Failure Records.
    • The driver information center, if equipped, may display a message.

Conditions for Clearing the DTC
    • A current DTC Last Test Failed clears when the diagnostic runs and passes.
    • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other non-emission related diagnostic.
    • Clear the DTC with a scan tool.

Test Description

The number below refers to the step number on the diagnostic table.

  1. This step attempts to pinpoint the location of the intermittent fault.

Step

Action

Yes

No

Schematic Reference: Engine Controls Schematics

Connector End View Reference: Engine Controls Connector End Views or Powertrain Control Module Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle

2

  1. Start the engine.
  2. Observe the DTC Information with a scan tool.

Are DTCs P0107 or P0651 also set?

Go to Diagnostic Trouble Code (DTC) List - Vehicle

Go to Step 3

3

  1. Turn OFF the ignition.
  2. Turn ON the ignition, with the engine OFF.
  3. Observe the MAP sensor parameter with the scan tool.
  4. Attempt to induce the fault that set the DTC by manipulating the following items:
    5. • The manifold absolute pressure (MAP) sensor wiring harness
    • The MAP sensor electrical connector
    • The powertrain control module (PCM) connector and wiring harness

Refer to Testing for Intermittent Conditions and Poor Connections.

Is the MAP sensor pressure affected during any part of the test?

Go to Step 4

Go to Step 8

4

Test the 5-volt reference circuit between the PCM and the MAP sensor for an open or for high resistance. Refer to Circuit Testing and Wiring Repairs.

Did you find and correct the condition?

Go to Step 8

Go to Step 5

5

Test the MAP sensor signal circuit between the PCM and the MAP sensor for the following intermittent conditions:

    • A short to ground
    • An open
    • High resistance

Refer to Circuit Testing and Wiring Repairs.

Did you find and correct the condition?

Go to Step 8

Go to Step 6

6

Test for an intermittent and for a poor connection at the MAP sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs.

Did you find and correct the condition?

Go to Step 8

Go to Step 7

7

Test for an intermittent and for a poor connection at the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs.

Did you complete the action?

Go to Step 8

--

8
  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.

Did the DTC fail this ignition?

Go to Step 2

Go to Step 9

9

Observe the Capture Info with a scan tool.

Are there any DTCs that have not been diagnosed?

Go to Diagnostic Trouble Code (DTC) List - Vehicle .

System OK