GM Service Manual Online
For 1990-2009 cars only

Inspections

Actions

DEFINITION: Fuel ignites in the intake manifold or in the exhaust system, making a loud popping noise.

Preliminary Inspections

    • Refer to Important Preliminary Inspections Before Beginning in Symptoms - Engine Controls .
    • Search for bulletins.
    • Inspect the powertrain control module (PCM) grounds for being clean, tight, and in the proper locations. Refer to Power and Grounding Component Views and Engine Controls Schematics .

Fuel System

    • Test for incorrect fuel pressure. Refer to Fuel System Diagnosis .
    • Inspect for a restricted fuel filter. Refer to Fuel System Diagnosis .
    • Inspect for a contaminated fuel condition. Refer to Alcohol/Contaminants-in-Fuel Diagnosis .
    • Test the fuel injectors. Refer to Fuel Injector Diagnosis .
    • Verify that each injector harness is connected to the correct injector or cylinder. Relocate injector harnesses as necessary.

Sensor/System

    • Inspect the crankcase ventilation system for proper operation.
    • Monitor the knock sensor (KS) system for excessive spark retard activity with a scan tool. Refer to Scan Tool Data List .

Ignition System

    • In order to properly inspect the spark plugs or to correct a condition, refer to the following procedures:
       -  Spark Plug Replacement
       -  Spark Plug Inspection
    • Remove spark plugs and inspect for the following:
       - Correct heat range
       - Wet plugs
       - Cracks
       - Wear
       - Improper gap
       - Burned electrodes
       - Heavy deposits
       - Verify that the spark plugs are of the correct type.
       - Inspect for proper ignition voltage output with J 26792 HEI Spark Tester .
    • An improper spark plug gap will cause a driveability condition. Gap the spark plugs using a wire gage gap tool.
    • If the spark plugs are found to be fouled, determine the cause before replacing the spark plugs.
    • Inspect for damaged or misaligned spark plug boots.
    • Monitor the Misfire Current Counters while driving the vehicle in the conditions that the symptom occurred. If a misfiring cylinder can be located, use the DTC P0300 table for diagnosis. Refer to DTC P0300 .

Engine Cooling System

    • Inspect the engine coolant level for being low. Refer to Loss of Coolant .
    • Inspect the engine thermostat for proper operation and for the correct heat range. Refer to Thermostat Diagnosis .

Engine Mechanical

    • Inspect engine mechanical for the following:
       - Compression
       - Sticking or leaking valves
       - Worn camshaft lobes
       - Valve timing
       - Worn rocker arms
       - Broken valve springs
       - Excessive oil in combustion chamber or leaking valve seals.
       - For more information, refer to one or more of the following procedures:
    • For incorrect, worn, or damaged basic engine parts. Inspect the following:
       - The camshaft--Refer to Camshafts Cleaning and Inspection .
       - The cylinder heads--Refer to Cylinder Head Cleaning and Inspection .
       - The pistons, etc.--Refer to Piston, Connecting Rod, and Bearing Cleaning and Inspection .

Additional Inspections

    • Visually and physically inspect the vacuum hoses for splits, kinks, and proper connections and routing as shown on the Vehicle Emission Control Information label.
    • Inspect the intake manifold and the exhaust manifold passages for casting flash.
    • Inspect the exhaust system for possible restrictions. Inspect the following:
       - Inspect the exhaust system for damaged or collapsed pipes.
       - Inspect the mufflers for heat distress or possible internal failure.
       - Inspect for possible plugged catalytic converter. Refer to Restricted Exhaust .
    • Electromagnetic interference (EMI) circuit can cause an engine misfire condition. A scan tool can usually detect EMI by monitoring the engine RPM. A sudden increase in RPM parameter with little change in actual engine RPM change may indicate that EMI is present. If a problem exists, inspect for high voltage components near the ignition control circuits.