Refer to
Engine Data Sensors
and
A/C Controls
for wiring view.
Circuit Description
The air conditioning (A/C) refrigerant pressure sensor responds to the changes in the A/C refrigerant high side pressure. This input indicates how much load the A/C compressor is putting on the engine, and is one of the factors used by the Powertrain Control Module (PCM) in order to determine the idle air control (IAC) position for the idle speed. The circuits consist of a 5 volt reference and a ground, both provided by the PCM, and a signal from the sensor. The signal is a voltage which is proportional to the A/C pressure. The sensor's operating range is between 0 and 459 psi. At 0 psi, the signal voltage will be about 0.1 volt, varying to about 4.9 volt at 459 psi.
Conditions for Setting the DTC
| • | The A/C refrigerant sensor pressure is greater than 453 psi (4.94 V) with A/C requested |
| Or |
| • | The A/C refrigerant sensor pressure is greater than 363 psi (4.0 V) with A/C not requested |
| Or |
| • | The A/C refrigerant sensor pressure is less than 0 psi (0.20 V) when the Air Temperature (IAT) is greater than 0°C (32°F) and DTCs P0112 or P0113 are not set |
| Or |
| • | The A/C refrigerant sensor pressure is less than 0 psi (0.10 V) when the Air Temperature (IAT) is greater than 0°C (32°F) and DTCs P0112 or P0113 are set. |
| • | Any of the above conditions met for 15 seconds. |
Action Taken When the DTC Sets
| • | The PCM will record the operating conditions at the time during which the diagnostic fails. This information will store in the Failure Records buffer. |
| • | A history DTC stores. |
| • | The PCM will disable the A/C compressor clutch. |
Conditions for Clearing the MIL/DTC
| • | A history DTC will clear after 40 consecutive warm up cycles without a fault. |
| • | A scan tool can clear the MIL/DTCs. |
Diagnostic Aids
| • | An intermittent DTC P0530 set along with a DTC P01406 indicates that the ground circuit is shorting to the 5 volt reference circuit. When this happens, the EGR Actual Position on the scan tool will display an incorrect value. Check the wiring harness for being rubbed through and shorting together or for a faulty A/C refrigerant pressure sensor. |
| • | DTC P0530 sets when the signal voltage falls outside the normal possible range of the sensor. If the actual pressure of the A/C system matches the scan tool readings, repair any A/C pressure problems before using this table. Refer to Air Conditioning System . |
| • | Any circuitry, that is suspected as causing the intermittent complaint, should be thoroughly checked for the following conditions: |
| - | Backed out terminals |
| - | Improper mating of the terminals |
| - | Broken locks |
| - | Improperly formed or damaged terminals |
| - | Poor terminal to wiring connections |
| - | Physical damage to the wiring harness |
Test Description
Number(s) below refer to the step number(s) on the Diagnostic Table.
-
The Powertrain OBD System Check prompts the technician to complete some basic checks and store the freeze frame and failure records data on the scan tool if applicable. This creates an electronic copy of the data taken when the fault occurred. The information is then stored on the scan tool for later reference.
-
If the MAP or TP sensor DTC is set, the faulty circuit is diagnosed in these tables. Refer to theappropriate table .
-
An open or poor connection in a shared sensor ground circuit will cause other DTCs to be set. If no other DTCs were set, the fault must be between the sensor and the circuit splice.
-
Determines if the low voltage signal was from the sensor or the signal circuit. Jumping the signal circuit to the 5 volt reference checks the circuits, connections and the PCM.
-
An open in a shared 5 volt reference circuit can cause other DTCs to be set. If no other DTCs were set, the circuit must be open between the sensor and the circuit splice.
-
Replacement PCMs must be reprogrammed. Refer to latest Techline information for programming procedures.
-
If no faults have been found at this point and no additional DTCs were set, refer to Diagnostic Aids for additional checks and information.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | |||
Were any MAP or TP DTCs also set? | -- | Go to MAP or TP DTC Tables | ||
3 | Does the A/C Highside value read greater than the specified value? | 4.0V (363 psi) | ||
4 | Disconnect the A/C pressure sensor electrical connector. Does the A/C High side value less than the specified value? | 1.0V (76 psi) | ||
5 | Is the A/C High side value less than the specified value? | 0.20V (0 psi) | ||
6 | With a DVM connected to B +, probe the A/C refrigerant pressure sensor ground circuit. Does the DVM measure the specified voltage? | B+ | ||
7 |
Does the DVM measure near the specified voltage? | 5.0V | ||
8 |
Does the A/C compressor clutch remain engaged? | -- | ||
9 | Replace the A/C refrigerant pressure sensor. Is the action complete? | -- | -- | |
Repair the open or poor connection in the A/C refrigerant pressure sensor ground circuit. Is the action complete? | -- | -- | ||
11 | Was the voltage measured on the A/C refrigerant pressure sensor signal circuit greater than the specified value? | 4.0V-6.0V | ||
Jumper the A/C refrigerant pressure sensor 5 volt reference and signal circuit terminals together. Does the scan tool A/C Highside value read greater than the specified value? | 4.6V (421 psi) | |||
Repair the open or poor connection in the A/C refrigerant pressure sensor 5 volt reference circuit. Is the action complete? | -- | -- | ||
14 |
Does the test light illuminate? | -- | ||
Replace the PCM. Is the action complete? | -- | -- | ||
16 | Check for a short to B+ in the A/C refrigerant pressure sensor signal circuit and repair as necessary. Was a repair necessary? | -- | ||
17 | Check the A/C refrigerant pressure sensor signal circuit for a short the 5 volt reference circuit and repair as necessary. | -- | ||
18 | With a DVM connected to B+, probe the A/C refrigerant pressure sensor signal circuit. Does the DVM read greater than the specified value? | 0.5V | ||
19 | Check the A/C compressor clutch relay control circuit for a short to ground and repair as necessary. Was a repair necessary? | -- | ||
20 | Did the A/C clutch disengage when the relay was removed? | -- | ||
21 | Check for a short ground or a short to the sensor ground in the A/C refrigerant pressure sensor signal circuit and repair as necessary. Was a repair necessary? | -- | ||
22 | Check for an open in the A/C refrigerant pressure sensor signal circuit and repair as necessary. Was a repair necessary? | -- | ||
23 | Replace the A/C compressor clutch relay. Is the action complete? | -- | -- | |
24 | Check for a short to B+ in the A/C compressor clutch ignition feed circuit, or for a faulty A/C compressor clutch. Is the action complete? | -- | -- | |
25 |
Does the scan tool indicate that this diagnostic has ran and passed? | -- | ||
Check if any additional DTCs are set. Are any DTCs displayed that has not been diagnosed? | -- | Go to applicable DTC table | System OK, Refer to Diagnostic Aids |
