GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2003 🢒 Corvette 🢒 Engine 🢒 Engine Controls - 5.7L 🢒 Fuel Injector Balance Test with Tech 2

Fuel Injector Balance Test with Tech 2 Without FFS

Table 1: Fuel Injector Balance Test Example (Typical)

Description

The scan tool is first used to energize the fuel pump. The scan tool is then used to pulse each injector for a precise amount of time, allowing a measured amount of fuel into the manifold. This causes a drop in system fuel pressure that can be recorded and used to compare the flow through each injector.

Fuel Injector Balance Test Example (Typical)

Cylinder

1

2

3

4

1st Reading

380 kPa (55 psi)

380 kPa (55 psi)

380 kPa (55 psi)

380 kPa (55 psi)

2nd Reading

215 kPa (31 psi)

201 kPa (29 psi)

208 kPa (30 psi)

229 kPa (33 psi)

Amount of Drop

165 kPa (24 psi)

179 kPa (26 psi)

172 kPa (25 psi)

151 kPa (22 psi)

Average Range: 156-176 kPa (22.5-25.5 psi)

Injector OK

Replace fuel injector - too much fuel pressure drop

Injector OK

Replace fuel injector - too little fuel pressure drop

Step

Action

Values

Yes

No

1

Did you perform the Diagnostic System Check-Engine Controls?

--

Go to Step 2

Go to Diagnostic System Check - Engine Controls

2

Did you perform the Fuel Injector Coil Test?

--

Go to Step 3

Go to Fuel Injector Solenoid Coil Test

3

Important: DO NOT perform this test if the ECT is above 94°C (201°F).

Important: Verify that adequate fuel is in the fuel tank before proceeding with this diagnostic.

  1. Install the fuel pressure gage. Refer to Fuel Pressure Gage Installation and Removal .
  2. Turn ON the ignition, with the engine OFF.

    3. Important: 

       • The fuel pump relay may need to be commanded ON a few times in order to obtain the highest possible fuel pressure.
       • DO NOT start the engine.

  3. Command the fuel pump relay ON with a scan tool.
  4. Observe the fuel pressure gage, with the fuel pump relay commanded ON.

Is the fuel pressure within the specified value?

380-427 kPa (55-62 psi)

Go to Step 4

Go to Fuel System Diagnosis

4

Important: The fuel pressure may vary slightly when the fuel pump stops operating. After the fuel pump stops operating, the fuel pressure should stabilize and remain constant.

Monitor the fuel pressure gage for 1 minute.

Does the fuel pressure decrease by more than the specified value?

34 kPa (5 psi)

Go to Fuel System Diagnosis

Go to Step 5

5

Notice: Do Not repeat any portion of this test before running the engine in order to prevent the engine from flooding.

  1. Select the Fuel Injector Balance Test function with a scan tool.
  2. Select an injector to be tested.
  3. Press Enter. This will prime the fuel system.
  4. Record the fuel pressure indicated by the fuel pressure gage after the fuel pressure stabilizes. This is the 1st pressure reading.

    5. Important: Record the fuel pressure value immediately after the fuel injector stops pulsing. The fuel pressure may rise after the fuel injector stops pulsing. Do not record the higher fuel pressure value.

  5. Energize the fuel injector by depressing the Pulse Injector button on the scan tool. This will energize the injector and decrease the fuel pressure.
  6. Record the fuel pressure indicated by the fuel pressure gage after the fuel injector has stopped pulsing. This is the 2nd pressure reading.
  7. Press Enter again to bring you back to the Select Injector screen.
  8. Repeat for each fuel injector.
  9. Subtract the 2nd pressure reading from the 1st pressure reading for one fuel injector. The result is the pressure drop value.
  10. Obtain a pressure drop value for each fuel injector.
  11. Add all of the individual pressure drop values. This is the total pressure drop.
  12. Divide the total pressure drop by the number of fuel injectors. This is the average pressure drop.

Is the difference between any individual pressure drop and the average pressure drop more than the specified value?

10 kPa (1.5 psi)

Go to Step 6

Go to Symptoms - Engine Controls

6

Replace the affected fuel injector. Refer to Fuel Injector Replacement .

Did you complete the replacement?

--

Go to Step 7

--

7

Operate the system in order to verify the repair.

Did you correct the condition?

--

System OK

Go to Symptoms - Engine Controls

Fuel Injector Balance Test with Tech 2 With FFS

Table 1: Fuel Injector Balance Test Example (Typical)

Description

The scan tool is first used to energize the fuel pump. The scan tool is then used to pulse each injector for a precise amount of time, allowing a measured amount of fuel into the manifold. This causes a drop in system fuel pressure that can be recorded and used to compare the flow through each injector.

Fuel Injector Balance Test Example (Typical)

Cylinder

1

2

3

4

1st Reading

380 kPa (55 psi)

380 kPa (55 psi)

380 kPa (55 psi)

380 kPa (55 psi)

2nd Reading

215 kPa (31 psi)

201 kPa (29 psi)

208 kPa (30 psi)

229 kPa (33 psi)

Amount of Drop

165 kPa (24 psi)

179 kPa (26 psi)

172 kPa (25 psi)

151 kPa (22 psi)

Average Range: 156-176 kPa (22.5-25.5 psi)

Injector OK

Replace fuel injector - too much fuel pressure drop

Injector OK

Replace fuel injector - too little fuel pressure drop

Step

Action

Values

Yes

No

1

Did you perform the Diagnostic System Check-Engine Controls?

--

Go to Step 2

Go to Diagnostic System Check - Engine Controls

2

Did you perform the Fuel Injector Coil Test?

--

Go to Step 3

Go to Fuel Injector Solenoid Coil Test

3

Important: DO NOT perform this test if the ECT is above 94°C (201°F).

Important: Verify that adequate fuel is in the fuel tank before proceeding with this diagnostic.

  1. Install the fuel pressure gage. Refer to Fuel Pressure Gage Installation and Removal .
  2. Turn ON the ignition, with the engine OFF.

    3. Important: The fuel pump relay may need to be commanded ON a few times in order to obtain the highest possible fuel pressure.

  3. Command the fuel pump relay ON with a scan tool.
  4. Observe the fuel pressure gage, with the fuel pump operating.

Is the fuel pressure within the specified value?

380-427 kPa (55-62 psi)

Go to Step 4

Go to Fuel System Diagnosis

4

Important: The fuel pressure will decrease when the fuel pump stops operating. After the fuel pump stops operating, the fuel pressure should stabilize and remain constant.

Monitor the fuel pressure gage for 5 minutes.

Does the fuel pressure decrease to less than the specified value?

350 kPa (51 psi)

Go to Fuel System Diagnosis

Go to Step 5

5

Notice: Do Not repeat any portion of this test before running the engine in order to prevent the engine from flooding.

  1. Select the Fuel Injector Balance Test function with a scan tool.
  2. Select an injector to be tested.
  3. Press Enter. This will prime the fuel system.
  4. Record the fuel pressure indicated by the fuel pressure gage after the fuel pressure stabilizes. This is the 1st pressure reading.

    5. Important: Record the fuel pressure value immediately after the fuel injector stops pulsing. The fuel pressure may rise after the fuel injector stops pulsing. Do not record the higher fuel pressure value.

  5. Energize the fuel injector by depressing the Pulse Injector button on the scan tool. This will energize the injector and decrease the fuel pressure.
  6. Record the fuel pressure indicated by the fuel pressure gage after the fuel injector has stopped pulsing. This is the 2nd pressure reading.
  7. Press Enter again to bring you back to the Select Injector screen.
  8. Repeat for each fuel injector.
  9. Subtract the 2nd pressure reading from the 1st pressure reading for one fuel injector. The result is the pressure drop value.
  10. Obtain a pressure drop value for each fuel injector.
  11. Add all of the individual pressure drop values. This is the total pressure drop.
  12. Divide the total pressure drop by the number of fuel injectors. This is the average pressure drop.

Is the difference between any individual pressure drop and the average pressure drop more than the specified value?

10 kPa (1.5 psi)

Go to Step 6

Go to Symptoms - Engine Controls

6

Replace the affected fuel injector. Refer to Fuel Injector Replacement .

Did you complete the replacement?

--

Go to Step 7

--

7

Operate the system in order to verify the repair.

Did you correct the condition?

--

System OK

Go to Symptoms - Engine Controls