GM Service Manual Online
For 1990-2009 cars only

Step

Action

Yes

No

Schematic Reference: Door Lock/Indicator Schematics and Door Control Module Schematics

Connector End View Reference: Power Door Systems Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2

Verify that the door ajar indicator is inoperative

Does the door ajar indicator operate normally?

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

Go to Step 3

3

Is the door ajar indicator inoperative?

Go to Step 4

Go to Step 7

4

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Open the appropriate door.
  4. With a scan tool, observe the appropriate door ajar switch parameter in the Body Control Module (BCM) data list.

Does the scan tool display Closed?

Go to Step 5

Go to Step 11

5

  1. Turn OFF the ignition.
  2. Disconnect the appropriate door latch harness connector.
  3. Connect a 3-amp fused jumper wire between the front door ajar switch signal circuit of the door latch harness connector and a good ground.
  4. Turn ON the ignition, with the engine OFF.

Does the door ajar indicator illuminate?

Go to Step 6

Go to Step 9

6

Connect a 3-amp fused jumper wire between the front door ajar switch signal circuit of the door latch harness connector and the ground circuit of the door latch harness connector.

Does the door ajar indicator illuminate?

Go to Step 12

Go to Step 14

7

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Close the appropriate door.
  4. With a scan tool, observe the appropriate door ajar switch parameter in the Body Control Module (BCM) data list.

Does the scan tool display Closed?

Go to Step 11

Go to Step 8

8

  1. Turn OFF the ignition.
  2. Disconnect the appropriate door latch harness connector.
  3. Turn ON the ignition, with the engine OFF.

Does the door ajar indicator turn off?

Go to Step 12

Go to Step 10

9

Test the appropriate front door ajar switch signal circuit for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 18

Go to Step 13

10

Test the appropriate front door ajar switch signal circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 18

Go to Step 13

11

Inspect for poor connections at the harness connectors of the instrument panel cluster (IPC). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 18

Go to Step 15

12

Inspect for poor connections at the harness connector of the appropriate door latch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 18

Go to Step 16

13

Inspect for poor connections at the harness connectors of the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 18

Go to Step 17

14

Locate and repair an open in the appropriate door latch ground circuit. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 18

--

15

Replace the IPC. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.

Did you complete the replacement?

Go to Step 18

--

16

Replace the appropriate door lock. Refer to Door Lock, Lock Bezel Replacement - Side Door .

Did you complete the replacement?

Go to Step 18

--

17

Replace the BCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.

Did you complete the replacement?

Go to Step 18

--

18

Operate the system in order to verify the repair.

Did you correct the condition?

System OK

Go to Step 2