GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2005 🢒 Corvette 🢒 Body 🢒 Instrument Panel, Gages, and Console 🢒 Steering Column Bracket Replacement

Removal Procedure
  1. Disable the SIR system. Refer to the following procedures in SIR:
    2. •  SIR Disabling and Enabling
    •  SIR Disabling and Enabling
    •  SIR Disabling and Enabling
  2. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
  3. Remove the instrument panel (I/P) assembly. Refer to Instrument Panel Assembly Replacement .
  4. Remove the upper and lower nuts retaining the steering column to the steering column bracket. Carefully rest the steering column on the I/P lower support beam. Refer to Steering Column Replacement in Steering Wheel and Column.

    5. Object Number: 174198 Size: SH
  5. Remove the accelerator pedal assembly with the accelerator pedal position sensor.
  6. Disconnect the brake master cylinder push rod from the brake pedal.
  7. Remove the brake booster mounting nuts.

    8. Object Number: 71494 Size: SH
  8. Remove the mounting bolts from the cruise control release switch bracket.
  9. Reposition the cruise control release switch and the bracket.

    10. Object Number: 71474 Size: SH
  10. Disconnect the master cylinder push rod from the clutch pedal.

    11. Object Number: 95665 Size: SH

    Important: The following step ensures proper trim fit during installation.

  11. Mark the location of the steering column bracket.
  12. Remove the bolts which secure the steering column bracket to the I/P lower support beam.

    13. Object Number: 95663 Size: SH
  13. Remove the bolts which secure the steering column bracket to the I/P upper support beam.
  14. Remove the steering column bracket.

Installation Procedure

    Object Number: 95663 Size: SH
  1. Install the steering column bracket into position as marked prior to removal.
  2. Install the bolts which secure the steering column bracket to the I/P upper support beam. Do NOT tighten the bolts.

    3. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 95665 Size: SH
  3. Install the bolts which secure the steering column bracket to the I/P lower support beam.

    4. Tighten
    Tighten both upper and locker bracket bolts to 10 N·m (89 lb in).


    Object Number: 71474 Size: SH
  4. Connect the master cylinder push rod to the clutch pedal.

    5. Object Number: 71494 Size: SH
  5. Position the cruise control release switch and bracket to the steering column bracket.
  6. Install the bracket bolts to the cruise control release switch.

    7. Tighten
    Tighten the bracket bolts to 12 N·m (106 lb in).


    Object Number: 174198 Size: SH
  7. Install the brake booster nuts.

    8. Tighten
    Tighten the nuts to 29 N·m (21 lb ft).

  8. Connect the master cylinder push rod to the brake pedal.
  9. Install the accelerator pedal assembly with the accelerator pedal position sensor.
  10. Install the left windshield side garnish molding. Refer to Windshield Side Garnish Molding Replacement in Interior Trim.
  11. Install the steering column to the steering column bracket. Refer to Steering Column Replacement in Steering Wheel and Column.
  12. Install the console. Refer to Console Replacement .
  13. Install the I/P assembly. Refer to Instrument Panel Assembly Replacement .
  14. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
  15. Enable the SIR system. Refer to the following procedures in SIR:
    16. •  SIR Disabling and Enabling
    •  SIR Disabling and Enabling
    •  SIR Disabling and Enabling