GM Service Manual Online
For 1990-2009 cars only

Removal Procedure

Notice: Always connect or disconnect the wiring harness connector from the EBCM/EBTCM with the ignition switch in the OFF position. Failure to observe this precaution could result in damage to the EBCM/EBTCM.

Important: 

   • The ignition switch must be placed in OFF mode ONLY, before disconnecting the negative battery cable during this procedure. If the ignition switch is accidentally placed into ignition ON engine OFF mode, the control modules will be activated and disconnecting the negative battery cable will cause various DTCs to be set. Refer to Keyless Entry System Description and Operation .
   • After the ignition switch is placed into OFF mode, a waiting period of 2 minutes must be observed to allow the high-speed LAN control modules to deactivate before disconnecting or connecting the negative battery cable during this procedure. If the waiting period is not observed, one or more of these control modules may still be active, this will cause various DTCs to be set.

  1. Place the ignition switch into OFF mode . Do NOT place the ignition switch into ignition ON engine OFF mode.
  2. Wait for a minimum of 2 minutes to allow the high-speed LAN control modules to deactivate.
  3. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  4. Thoroughly clean the electronic brake control module (EBCM) to brake pressure modulator valve (BPMV) area of any dirt or contaminants.
  5. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .

  6. Object Number: 1274761  Size: SH
  7. Remove the two BPMV bracket bolts to improve access to the EBCM and connector.
  8. Support the ABS modulator assembly.
  9. Disconnect the electrical connector from the brake fluid pressure sensor.

  10. Object Number: 899234  Size: SH
  11. Depress the lock tab and release the cam (2) to disconnect the electrical connector from the EBCM (3).

  12. Object Number: 772017  Size: SH
  13. Remove the 4 EBCM-to-BPMV retaining bolts.
  14. Separate the EBCM (1) from the BPMV (2) by carefully pulling apart.

Installation Procedure


    Object Number: 772017  Size: SH
  1. Clean the sealing surface of the BPMV with denatured alcohol, or equivalent, and a clean shop cloth.
  2. Ensure the motor connector (3) is in place on the EBCM (1).
  3. Install the EBCM to the BPMV. Use care when aligning the EBCM (1) to the BPMV electrical terminals (2).
  4. Notice: Refer to Fastener Notice in the Preface section.

  5. Install the 4 EBCM-to-BPMV bolts. Tighten the bolts in a criss-cross pattern.
  6. Tighten

        • First pass: Tighten the bolts to 3 N·m (27 lb in).
        • Second pass: Tighten the bolts to 6 N·m (53 lb in).

    Object Number: 899234  Size: SH
  7. Connect the electrical connector to the EBCM (3). Ensure the cam (2) is secured by the lock tab.
  8. Connect the electrical connector to the brake fluid pressure sensor.

  9. Object Number: 1274761  Size: SH
  10. Install the two BPMV bracket bolts.
  11. Tighten
    Tighten the bolts to 27 N·m (20 lb ft).

  12. Lower the vehicle.
  13. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  14. If installing a replacement module, refer to Service Programming System (SPS) .
  15. If installing a replacement module, program the replacement module. Refer to Control Module References .
  16. Perform the Diagnostic System Check - Vehicle .