Tool Required

1. Remove the drain plug and washer (1) and allow the fluid to drain.



2. To drain the fluid from models equipped with a pump and cooler, perform the following steps:

2.1.	Remove the bolt (1) retaining the lower inlet pipe clamp.

2.2.	Using a bent tip screwdriver, remove the quick connect fitting retaining ring (3) from the quick connect fitting (4), and discard the retaining ring.

2.3.	Drain the fluid by pulling the lower inlet pipe (2) straight out of the quick connect fitting.




3. For models equipped with a pump and cooler, perform the following steps to remove the cooler and pipes:

3.1.	Using the J 41623-B , remove the inlet and outlet pipes by aligning notches on the J 41623-B with quick connect fittings (2, 4, 6) and rotating the tool to release pipes (3 and 5) from the quick connect fittings.

3.2.	Remove the 3 cooler retaining bolts (8).

3.3.	Remove the cooler (7).




4. Remove the fill plug and washer (1).



5. Remove the vehicle speed sensor and bolt, if equipped.



6. Remove the left cover (3) and bolts (2).
7. Remove the O-ring (4) and oil seal (1) from the cover.
8. Remove the magnet (5) and dowel (6) from the carrier.
9. Remove the oil trough (7).



10. Install the differential assembly (1) onto the J 42173  (2).

Notice: Refer to Fastener Notice in the Preface section.

11. Install 4 M8 x 1.25 bolts (3).

Tighten
Tighten the bolts to 30 N·m (22 lb ft).





Important: Z06 models require the modification of J 42173 , using J-42173-10 .

12. Install the differential assembly (1) onto the J 42173  (2).
13. Install 2 M8 x 1.25 bolts (3).

Tighten
Tighten the bolts to 30 N·m (22 lb ft).




14. Using a punch, remove the cover alignment pin.



15. Remove the right cover (3) and bolts (2) from the differential.
16. Remove the O-ring (4) and oil seal (1) from the cover.



17. Remove the rear cover (2), bolts (3), and gasket (1), or pump - some models (4).



18. Install 2 M10 x 1.5 nuts onto the transmission stud. Remove the stud from the differential, if equipped.



19. Remove the C-clip from the output shaft.



20. Install the J 42155 into the groove of the output shaft in order to remove the differential case assembly.



21. Remove the pinion housing/cage bolts.



22. Using the J 25070 , heat the differential housing around the pinion housing. Heating the housing will ease in pinion removal.
23. Remove the pinion housing/cage assembly (1) and shims (2) from the differential housing. Mark or tag the shims for assembly.

Locate 2 screwdrivers or pry bars to the flange area of the pinion housing/cage to ease in removal.




24. Install the DT-47596  (2) into the right cover. Tighten securely into the bearing cup.
25. Place J 45124  (1) over DT-47596  (2). Adjust legs for best fit. Install supplied bolt, nut, thrust bearing and washer. Hold the bolt and tighten the nut to remove the bearing cup and shim.



26. Remove the bearing cup (1) and shim (2). Mark or tag the shims for assembly.



27. Install the DT-47596  (2) into the differential housing, behind the left bearing cup. Tighten securely into the bearing cup.
28. Place J 45124  (1) over DT-47596  (2). Adjust legs for best fit. Install supplied bolt, nut, thrust bearing and washer. Hold the bolt and tighten the nut to remove the bearing cup and shim.
29. Remove the cup (2) and shim (1) from the differential housing. Mark or tag the shims for assembly.