GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC P0461: Fuel Level Sensor 1 Circuit Performance

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Fuel Level Sensor Reference Voltage Circuit

P0462

P2067

--

--

P0461

P2066 or P2636

Fuel Level Sensor 1 Signal Circuit

Fuel Level Sensor 2 Signal Circuit

P0462

P2067

P0463

P2068

P0464

P0463

P2068

P0461

P2066 or P2636

Fuel Level Sensor Low Reference Circuit

--

P0463

P2068

P0464

P0463

P2068

P0461

P2066 or P2636

Circuit/System Description

The primary fuel level sender and the secondary fuel level sender changes resistance based on fuel level. The engine control module (ECM) monitors the signal circuits of the primary fuel level sender and the secondary fuel level sender in order to determine the fuel level. When the fuel tank is full, the resistances of both fuel level senders are low and the ECM senses a low signal voltage on both the signal circuits of the primary fuel level sender and the secondary fuel level sender. When the fuel tanks are empty, the resistances of the fuel level senders are high and the ECM senses a high signal voltage. The ECM uses the signal circuits of the primary fuel level sender and the secondary fuel level sender in order to calculate the percentage of remaining fuel in the tank. The ECM sends the fuel level percentage via serial data circuit to the instrument cluster in order to control the fuel gage.

Diagnostic Aids

Check if DTC P2066 is also set. Both DTCs P0461 and P2066 may set simultaneously if the vehicle was refueled with the ignition ON or engine RUNNING. Always refuel with the ignition OFF.

Conditions for Running the DTC

    • The engine is running.
    • No VSS DTCs are set.

Conditions for Setting the DTC

    • The ECM detects that the primary fuel tank is greater than 28.5 L (7.5 gal) and the secondary fuel tank is less than 3.3 L (.87 gal) over a distance of 200 km (124.2 mi).
    • The ECM detects that the primary fuel tank is less than 28.5 L (7.5 gal) and no change in primary tank of at least 3 L (.79 gal) over a distance of 80 km (49.7 mi).

Action Taken When the DTC Sets

    • The fuel gage defaults to empty.
    • The driver information center (DIC) displays the FUEL LEVEL LOW message.
    • The ECM records the operating conditions at the time that the diagnostic test fails. The ECM displays the failure information in the Failure Records on the scan tool.

Conditions for Clearing the DTC

    • The DTC becomes history when the conditions for setting the DTC are no longer present.
    • The history DTC clears after 40 malfunction-free warm-up cycles.

Reference Information

Schematic Reference

    •  Instrument Cluster Schematics
    •  Engine Controls Schematics for the 6.0L engine
    •  Engine Controls Schematics for the 7.0L engine

Connector End View Reference

    •  Displays and Gages Connector End Views
    •  Engine Control Module Connector End Views for the 6.0L engine
    •  Engine Control Module Connector End Views for the 7.0L engine

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Scan Tool Data List

Circuit/System Testing

  1. Ignition OFF, remove the primary fuel level sender and verify there are no obstructions interfering with the fuel level sender.
  2. Repair any fuel level sender interference.
  3. If no interference is present, perform the fuel level sensor component test before replacing the primary fuel level sensor.

Component Testing

  1. Ignition OFF, disconnect the harness connector at the primary fuel level sensor.
  2. While sweeping the primary fuel level sensor through its full range of motion, test for a minimum value less than 41 ohms and a maximum value greater than 119 ohms of resistance between signal terminal 1 and the low reference terminal 4.
  3. If not within the specified range, replace the primary fuel level sensor.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Fuel Level Sensor Replacement - Left Side for the 6.0L engine
    •  Fuel Level Sensor Replacement - Left Side for the 7.0L engine
    •  Control Module References for the ECM replacement, setup, and programming