GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The brake pedal position (BPP) sensor is an input to the electronic brake control module (EBCM). The BPP sensor is a potentiometer type sensor with a 5-volt reference circuit and a low reference circuit. The body control module (BCM) supplies the 5-volt reference to the BPP.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC C0161 ABS/TCS Brake Switch Circuit

DTC Symptom

DTC Symptom Descriptor

11

Above Maximum Threshold

12

Below Minimum Threshold

Conditions for Running the DTC

C0161 11

    • The ignition is ON.
    • The vehicle speed is greater than 16 km/h (10 mph).
    • The ignition voltage is greater than 8 volts.

C0161 12

    • The ignition is ON.
    • The ignition voltage is greater than 8 volts.

Conditions for Setting the DTC

C0161 11

    • The brake pedal is sensed as applied.
    • The vehicle speed is greater than 40 km/h (25 mph).
    • The vehicles acceleration exceeds 8 km/h per second (5 mph per second).

C0161 12

    • Brake pedal is not applied.
    • Master cylinder pressure is greater than 150 psi.
    • The vehicle speed is greater than 24 km/h (14 mph).
    • The vehicles deceleration exceeds 11.5 km/h per second (7 mph per second).

Action Taken When the DTC Sets

If equipped, the following actions occur:

    • The EBCM disables the engine drag control (EDC)/tire pressure monitor (TPM)/vehicle stability enhancement system (VSES) for the duration of the ignition cycle.
    • The Traction Control System (TCS) is degraded.
    • The Traction Control and Active Handling indicator turns ON.
    • The driver information center (DIC) displays the following messages:
       - Service Traction System
       - Service Active Handling
    • The ABS remains functional.

Conditions for Clearing the DTC

    • The condition for the DTC is no longer present and the DTC is cleared with a scan tool.
    • The EBCM automatically clears the history DTC when a current DTC is not detected in 100 consecutive drive cycles.

Diagnostic Aids

C0161 11

Possible causes of this DTC are the following conditions:

    • The BPP sensor circuit is shorted to voltage.
    • The BPP sensor needs recalibration.
    • A brake pedal that is binding

C0161 12

Possible causes of this DTC are the following conditions:

    • A signal circuit of the BPP sensor is open.
    • The BPP sensor needs recalibration.
    • All brake lamps are open.
    • All brake lamp grounds are open.
    • An internal BPP sensor malfunction

Test Description

The number below refers to the step number on the diagnostic table.

  1. Test for the current state of the brake pedal position sensor.

Step

Action

Yes

No

Schematic Reference: Antilock Brake System Schematics

1

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle

2

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, observe the brake pedal position sensor (BPP) Reference Signal parameter in the exterior lamps data list.

Does the scan tool display Released?

Go to Step 3

Go to Step 4

3

  1. Press the brake pedal.
  2. With a scan tool, observe the BPP Reference Signal parameter.

Does the BPP Reference Signal parameter change state?

Go to Diagnostic Aids

Go to Step 4

4

  1. Turn OFF the ignition.
  2. Inspect the BPP sensor and calibrate if needed.

Did you find and correct the condition?

Go to Step 11

Go to Step 5

5

  1. Turn OFF the ignition.
  2. Disconnect the BPP sensor connector.
  3. Turn ON the ignition, with the engine OFF.
  4. With a scan tool, observe the BPP Reference Signal parameter.

Does the scan tool display Released?

Go to Step 8

Go to Step 6

6

Test the BPP sensor signal circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 11

Go to Step 7

7

Inspect for poor connections at the harness connector of the electronic brake control module (EBCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

Go to Step 11

Go to Step 9

8

Inspect for poor connections at the harness connector of the BPP sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

Go to Step 11

Go to Step 10

9

Replace the EBCM. Refer to Control Module References for replacement, setup, and programming.

Did you complete the repair?

Go to Step 11

--

10

Replace the BPP sensor. Refer to Brake Pedal Position Sensor Replacement .

Did you complete the repair?

Go to Step 11

--

11

  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

Go to Step 2

System OK