GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2008 🢒 Corvette 🢒 Preface 🢒 Cautions and Notices 🢒 Rear Brake Caliper Replacement

Rear Brake Caliper Replacement JL9-J55

Removal Procedure

Caution: Refer to Brake Fluid Irritant Caution in the Preface section.

Notice: Refer to Brake Fluid Effects on Paint and Electrical Components Notice in the Preface section.

  1. Inspect the fluid level in the brake master cylinder reservoir.
  2. If the brake fluid level is midway between the maximum-full point and the minimum allowable level, no brake fluid needs to be removed from the reservoir before proceeding.
  3. If the brake fluid level is higher than midway between the maximum-full point and the minimum allowable level, remove brake fluid to the midway point before proceeding.
  4. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle.
  5. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation.

    6. Object Number: 63948 Size: SH
  6. Remove the brake caliper inlet fitting bolt from the caliper.
  7. Remove the brake hose from the brake caliper.
  8. Remove and discard the 2 copper brake hose gaskets. These gaskets may be stuck to the brake caliper and/or the brake hose end.
  9. Plug the opening in the brake caliper and the brake hose to prevent fluid loss and contamination.

    10. Object Number: 63989 Size: SH
  10. Remove the brake caliper guide pin bolts.
  11. Remove the brake caliper from the caliper mounting bracket.

Installation Procedure
  1. Inspect the caliper slide boots for cuts, tears, or deterioration. If damaged, replace the slides and the boots. Refer to Rear Disc Brake Hardware Replacement.

    2. Object Number: 63989 Size: SH
  2. Install the brake caliper to the caliper mounting bracket.

    3. Notice: Refer to Fastener Notice in the Preface section.

  3. Install the brake caliper guide pin bolts.

    4. Tighten
    Tighten the brake caliper guide pin bolts to 31 N·m (23 lb ft).


    Object Number: 63948 Size: SH
  4. Remove the plug from the brake caliper opening and the brake hose.

    5. Important: Install NEW copper brake hose gaskets.

  5. Assemble the NEW copper brake hose gaskets, and the brake caliper inlet fitting bolt to the brake hose.
  6. Install the brake hose and the brake caliper inlet fitting bolt to the brake caliper.

    7. Tighten
    Tighten the brake caliper inlet fitting bolt to 45 N·m (33 lb ft).

  7. Bleed the hydraulic brake system. Refer to Hydraulic Brake System Bleeding.
  8. Install the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation.
  9. Lower the vehicle.

Rear Brake Caliper Replacement J56


Object Number: 1673764 Size: SF

Callout

Component Name

Caution: Refer to Brake Dust Caution in the Preface section.

Caution: Refer to Brake Fluid Irritant Caution in the Preface section.

Preliminary Procedure

  1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle.
  2. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation.
  3. Remove the brake hose from the caliper. Refer to Rear Brake Hose Replacement.

1

Brake Caliper Bolt

Notice: Refer to Fastener Notice in the Preface section.

Tighten
175 N·m (129 lb ft)

2

Brake Caliper

Tip

    • If removing the caliper to service the brake system, support the caliper with mechanics wire.
    • Plug the brake caliper hose fitting inlet port to prevent brake fluid loss and contamination.
    • Bleed the hydraulic brake system. Refer to Hydraulic Brake System Bleeding.