DTC P0120, P0122, P0123, P0220, P0222, P0223, or P2135 W/LS3 or LS7
Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptors
DTC P0120: Throttle Position (TP) Sensor 1 CircuitDTC P0122: Throttle Position (TP) Sensor 1 Circuit Low Voltage
DTC P0123: Throttle Position (TP) Sensor 1 Circuit High Voltage
DTC P0220: Throttle Position (TP) Sensor 2 Circuit
DTC P0222: Throttle Position (TP) Sensor 2 Circuit Low Voltage
DTC P0223: Throttle Position (TP) Sensor 2 Circuit High Voltage
DTC P2135: Throttle Position (TP) Sensor 1-2 Correlation
Diagnostic Fault Information
Circuit | Short to Ground | High Resistance | Open | Short to Voltage | Signal Performance |
|---|---|---|---|---|---|
TP Sensor 1 Signal | P0122 | P2135 | P0122 | P0123 | P0068, P0121 |
TP Sensor 1 5-Volt Reference | P0122 | P2135 | P0122 | P0123 | -- |
TP Sensor 1 Low Reference | -- | P2135 | P0123 | -- | -- |
TP Sensor 2 Signal | P0222 | P2135 | P0223 | P0223 | P0068, P0121 |
TP Sensor 2 5-Volt Reference | P0222 | P2135 | P0222 | P0223 | -- |
TP Sensor 2 Low Reference | -- | P2135 | P0223 | -- | -- |
Typical Scan Tool Data
Circuit | Short to Ground | Open | Short to Voltage |
|---|---|---|---|
Operating Conditions: Engine running at various operating conditions Normal Range: 4.75-0.35 V | |||
TP Sensor 1 Signal | 0 V | 0 V | 5 V |
TP Sensor 1 5-Volt Reference | 0 V | 0 V | 5 V |
TP Sensor 1 Low Reference | -- | 5 V | -- |
Circuit | Short to Ground | Open | Short to Voltage |
|---|---|---|---|
Operating Conditions: Engine running at various operating conditions Parameter Normal Range: 0.25-4.59 V | |||
TP Sensor 2 Signal | 0 V | 5 V | 5 V |
TP Sensor 2 5-Volt Reference | 0 V | 0 V | 5 V |
TP Sensor 2 Low Reference | -- | 5 V | -- |
Circuit/System Description
The throttle actuator control (TAC) system uses two throttle position (TP) sensors to monitor the throttle position. The TP sensors 1 and 2 are located within the throttle body assembly. Each sensor has the following circuits:
| • | A 5-volt reference circuit |
| • | A low reference circuit |
| • | A signal circuit |
Two processors are also used to monitor the TAC system data. Both processors are located within the engine control module (ECM). Each signal circuit provides both processors with a signal voltage proportional to throttle plate movement. Both processors monitor each other's data to verify that the indicated TP calculation is correct.
Conditions for Running the DTC
P0120, P0122, P0123, P0220, P0222, and P0223
| • | DTC P0601, P0602, P0603, P0604, P0606, P0607, P0641, P0651 are not set. |
| • | The system voltage is more than 5.23 volts. |
| • | The ignition is in the Unlock/Accessory or Run position. |
| • | DTC P0120, P0122, P0123, P0220, P0222, P0223 run continuously when the above conditions are met. |
P2135
| • | The system voltage is more than 5.23 volts. |
| • | The ignition is in the Unlock/Accessory or Run position. |
| • | DTC P0120, P0220, P0641, P0651 are not set. |
| • | DTC P2135 runs continuously when the above conditions are met. |
Conditions for Setting the DTC
P0120
TP sensor 1 voltage is less than 0.325 volt or more than 4.75 volts for more than 1 second.
P0122
The ECM detects that the TP sensor 1 voltage is less than 0.325 volt for more than 1 second.
P0123
The ECM detects that the TP sensor 1 voltage is more than 4.75 volts for more than 1 second.
P0220
The TP sensor 2 voltage is less than 0.25 volt or more than 4.59 volts for more than 1 second.
P0222
The ECM detects that the TP sensor 2 voltage is less than 0.25 volt for more than 1 second.
P0223
The ECM detects that the TP sensor 2 voltage is more than 4.59 volts for more than 1 second.
P2135
The difference between the TP sensor 1 and TP sensor 2 exceeds a predetermined value for more than 2 seconds.
Action Taken When the DTC Sets
| • | DTCs P0120, P0122, P0123, P0220, P0222, P0223, and P2135 are Type A DTCs. |
| • | The control module commands the TAC system to operate in the Reduced Engine Power mode. |
| • | A message center or an indicator displays Reduced Engine Power. |
| • | Under certain conditions the control module commands the engine OFF. |
Conditions for Clearing the MIL/DTC
DTCs P0120, P0122, P0123, P0220, P0222, P0223, and P2135 are Type A DTCs.
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Throttle Actuator Control (TAC) System Description
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
- Ignition ON, observe the scan tool TP sensor 1 voltage parameter. The reading should be between 4.75-0.35 volts and change with accelerator pedal input.
- Ignition ON, observe the scan tool TP sensor 2 voltage parameter. The reading should be between 0.25-4.59 volts and change with accelerator pedal input.
- Ignition ON, observe the scan tool TP sensor 1 and 2 parameter. The scan tool should indicate agree.
- Clear the DTCs with the scan tool. Operate the vehicle within the Conditions for Running the DTC, or within the conditions that you observed from the Freeze Frame/Failure Records.
- Verify that DTC P0120 or P0220 are not the only throttle position DTCs set.
- Verify that DTCs P0641 or P0651 are not set.
- Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.
| ⇒ | If DTC P0120 or P0220 are the only DTCs set, replace the control module. |
| ⇒ | If DTC P0641 or P0651 is set, refer to DTC P0641 or P0651. |
Circuit/System Testing
- Ignition OFF, disconnect the harness connector at the throttle body. Allow up to 2 minutes for the ECM to completely power down.
- Ignition OFF, test for less than 5 ohms between the low reference circuit terminal C and ground.
- Ignition ON, test for 4.8-5.2 volts between 5-volt reference circuit terminal E and ground.
- Verify the scan tool TP sensor 1 voltage is less than 0.1 volt.
- Verify the scan tool TP sensor 2 voltage is greater than 4.8 volts.
- Install a 3A fused jumper wire between the signal circuit terminal D and the 5-volt reference circuit terminal E of the TP sensor 1. Verify the TP sensor 1 voltage is greater than 4.8 volts.
- Install a test lamp between the signal circuit terminal F of the TP sensor 2 and ground. The test lamp should not illuminate.
- Install a 3A fused jumper wire between the signal circuit terminal F and the low reference circuit terminal C of the TP sensor 2. Verify that the TP sensor 2 voltage is less than 0.1 volt.
- Ignition OFF, disconnect the harness connector at the ECM.
- Test for less than 5 ohms on all TP sensor circuits between the following terminals:
- Test for infinite resistance between TP sensor 1 signal circuit terminal D and TP sensor signal circuit terminal F.
- If all circuits test normal, replace the throttle body.
| ⇒ | If greater than 5 ohms, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM. |
| ⇒ | If less than 4.8 volts, test 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM. |
| ⇒ | If greater than 5.2 volts, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the ECM. |
| ⇒ | If greater than 0.1 volt, test the signal circuit terminal D for a short to voltage. If the circuit tests normal, replace the ECM. |
| ⇒ | If less than 4.8 volts, test the signal circuit terminal F for a short to ground. If the circuit tests normal, replace the ECM. |
| ⇒ | If less than 4.8 volts, test the TP sensor 1 signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM. |
| ⇒ | If the test lamp illuminates, test the TP sensor 2 signal circuit for a short to voltage. If the circuit tests normal, replace the ECM. |
| ⇒ | If greater than 1.0 volt, test the TP sensor 2 signal circuit for an open/high resistance. If the circuit tests normal, replace the ECM. |
| • | ECM X2 signal circuit terminal 65 to TP terminal D |
| • | ECM X2 signal circuit terminal 63 to TP terminal F |
| • | ECM X2 5-volt reference circuit terminal 3 to terminal E |
| ⇒ | If greater than 5 ohms, repair the affected circuit for open/high resistance. |
| ⇒ | If less than infinite resistance, repair the short between TP sensor 1 signal circuit and TP sensor 2 signal circuit. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for ECM replacement, setup, and programming |
DTC P0120, P0122, P0123, P0220, P0222, P0223, or P2135 W/LS9
Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptors
DTC P0120: Throttle Position (TP) Sensor 1 CircuitDTC P0122: Throttle Position (TP) Sensor 1 Circuit Low Voltage
DTC P0123: Throttle Position (TP) Sensor 1 Circuit High Voltage
DTC P0220: Throttle Position (TP) Sensor 2 Circuit
DTC P0222: Throttle Position (TP) Sensor 2 Circuit Low Voltage
DTC P0223: Throttle Position (TP) Sensor 2 Circuit High Voltage
DTC P2135: Throttle Position (TP) Sensor 1-2 Correlation
Diagnostic Fault Information
Circuit | Short to Ground | High Resistance | Open | Short to Voltage | Signal Performance |
|---|---|---|---|---|---|
TP Sensor 1 Signal | P0122 | P2135 | P0122 | P0123 | P0068, P0121 |
TP Sensor 1 5-Volt Reference | P0122 | P2135 | P0122 | P0123 | -- |
TP Sensor 1 Low Reference | -- | P2135 | P0123 | -- | -- |
TP Sensor 2 Signal | P0222 | P2135 | P0223 | P0223 | P0068, P0121 |
TP Sensor 2 5-Volt Reference | P0222 | P2135 | P0222 | P0223 | -- |
TP Sensor 2 Low Reference | -- | P2135 | P0223 | -- | -- |
Typical Scan Tool Data
Circuit | Short to Ground | Open | Short to Voltage |
|---|---|---|---|
Operating Conditions: Engine running at various operating conditions Normal Range: 4.75-0.35 V | |||
TP Sensor 1 Signal | 0 V | 0 V | 5 V |
TP Sensor 1 5-Volt Reference | 0 V | 0 V | 5 V |
TP Sensor 1 Low Reference | -- | 5 V | -- |
Circuit | Short to Ground | Open | Short to Voltage |
|---|---|---|---|
Operating Conditions: Engine running at various operating conditions Parameter Normal Range: 0.25-4.59 V | |||
TP Sensor 2 Signal | 0 V | 5 V | 5 V |
TP Sensor 2 5-Volt Reference | 0 V | 0 V | 5 V |
TP Sensor 2 Low Reference | -- | 5 V | -- |
Circuit/System Description
The throttle actuator control (TAC) system uses two throttle position (TP) sensors to monitor the throttle position. The TP sensors 1 and 2 are located within the throttle body assembly. Each sensor has the following circuits:
| • | A 5-volt reference circuit |
| • | A low reference circuit |
| • | A signal circuit |
Two processors are also used to monitor the TAC system data. Both processors are located within the engine control module (ECM). Each signal circuit provides both processors with a signal voltage proportional to throttle plate movement. Both processors monitor each other's data to verify that the indicated TP calculation is correct.
Conditions for Running the DTC
P0120, P0122, P0123, P0220, P0222, and P0223
| • | DTC P0601, P0602, P0603, P0604, P0606, P0607, P0641, P0651 are not set. |
| • | The system voltage is more than 5.23 volts. |
| • | The ignition is in the Unlock/Accessory or Run position. |
| • | DTC P0120, P0122, P0123, P0220, P0222, P0223 run continuously when the above conditions are met. |
P2135
| • | The system voltage is more than 5.23 volts. |
| • | The ignition is in the Unlock/Accessory or Run position. |
| • | DTC P0120, P0220, P0641, P0651 are not set. |
| • | DTC P2135 runs continuously when the above conditions are met. |
Conditions for Setting the DTC
P0120
TP sensor 1 voltage is less than 0.325 volt or more than 4.75 volts for more than 1 second.
P0122
The ECM detects that the TP sensor 1 voltage is less than 0.325 volt for more than 1 second.
P0123
The ECM detects that the TP sensor 1 voltage is more than 4.75 volts for more than 1 second.
P0220
The TP sensor 2 voltage is less than 0.25 volt or more than 4.59 volts for more than 1 second.
P0222
The ECM detects that the TP sensor 2 voltage is less than 0.25 volt for more than 1 second.
P0223
The ECM detects that the TP sensor 2 voltage is more than 4.59 volts for more than 1 second.
P2135
The difference between the TP sensor 1 and TP sensor 2 exceeds a predetermined value for more than 2 seconds.
Action Taken When the DTC Sets
| • | DTCs P0120, P0122, P0123, P0220, P0222, P0223, and P2135 are Type A DTCs. |
| • | The control module commands the TAC system to operate in the Reduced Engine Power mode. |
| • | A message center or an indicator displays Reduced Engine Power. |
| • | Under certain conditions the control module commands the engine OFF. |
Conditions for Clearing the MIL/DTC
DTCs P0120, P0122, P0123, P0220, P0222, P0223, and P2135 are Type A DTCs.
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Throttle Actuator Control (TAC) System Description
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
- Ignition ON, observe the scan tool TP sensor 1 voltage parameter. The reading should be between 4.75-0.35 volts and change with accelerator pedal input.
- Ignition ON, observe the scan tool TP sensor 2 voltage parameter. The reading should be between 0.25-4.59 volts and change with accelerator pedal input.
- Ignition ON, observe the scan tool TP sensor 1 and 2 parameter. The scan tool should indicate agree.
- Clear the DTCs with the scan tool. Operate the vehicle within the Conditions for Running the DTC, or within the conditions that you observed from the Freeze Frame/Failure Records.
- Verify that DTC P0120 or P0220 are not the only throttle position DTCs set.
- Verify that DTCs P0641 or P0651 are not set.
- Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.
| ⇒ | If DTC P0120 or P0220 are the only DTCs set, replace the control module. |
| ⇒ | If DTC P0641 or P0651 is set, refer to DTC P0641 or P0651. |
Circuit/System Testing
- Ignition OFF, disconnect the harness connector at the throttle body. Allow up to 2 minutes for the ECM to completely power down.
- Ignition OFF, test for less than 5 ohms between the low reference circuit terminal C and ground.
- Ignition ON, test for 4.8-5.2 volts between 5-volt reference circuit terminal E and ground.
- Verify the scan tool TP sensor 1 voltage is less than 0.1 volt.
- Verify the scan tool TP sensor 2 voltage is greater than 4.8 volts.
- Install a 3A fused jumper wire between the signal circuit terminal D and the 5-volt reference circuit terminal E of the TP sensor 1. Verify the TP sensor 1 voltage is greater than 4.8 volts.
- Install a test lamp between the signal circuit terminal F of the TP sensor 2 and ground. The test lamp should not illuminate.
- Install a 3A fused jumper wire between the signal circuit terminal F and the low reference circuit terminal C of the TP sensor 2. Verify that the TP sensor 2 voltage is less than 0.1 volt.
- Ignition OFF, disconnect the harness connector at the ECM.
- Test for less than 5 ohms on all TP sensor circuits between the following terminals:
- Test for infinite resistance between TP sensor 1 signal circuit terminal D and TP sensor signal circuit terminal F.
- If all circuits test normal, replace the throttle body.
| ⇒ | If greater than 5 ohms, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM. |
| ⇒ | If less than 4.8 volts, test 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM. |
| ⇒ | If greater than 5.2 volts, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the ECM. |
| ⇒ | If greater than 0.1 volt, test the signal circuit terminal D for a short to voltage. If the circuit tests normal, replace the ECM. |
| ⇒ | If less than 4.8 volts, test the signal circuit terminal F for a short to ground. If the circuit tests normal, replace the ECM. |
| ⇒ | If less than 4.8 volts, test the TP sensor 1 signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM. |
| ⇒ | If the test lamp illuminates, test the TP sensor 2 signal circuit for a short to voltage. If the circuit tests normal, replace the ECM. |
| ⇒ | If greater than 1.0 volt, test the TP sensor 2 signal circuit for an open/high resistance. If the circuit tests normal, replace the ECM. |
| • | ECM X2 signal circuit terminal 64 to TP terminal D |
| • | ECM X2 signal circuit terminal 66 to TP terminal F |
| • | ECM X2 5-volt reference circuit terminal 44 to terminal E |
| ⇒ | If greater than 5 ohms, repair the affected circuit for open/high resistance. |
| ⇒ | If less than infinite resistance, repair the short between TP sensor 1 signal circuit and TP sensor 2 signal circuit. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for ECM replacement, setup, and programming |
