Circuit Description
As the wheel is rotated, the speed sensor produces an AC voltage that increases with wheel speed. The electronic brake control module (EBCM) uses the frequency of the AC signal to calculate the wheel speed. The speed sensor is connected to the EBCM by a twisted pair of wires. Twisting reduces noise susceptibility that may cause a DTC to set.
Conditions for Setting the DTC
All of the following must be true for DTC C1207 to set:
| • | DTC C1200, C1203, C1206, or C1209 not current |
| • | Brake switch OFF |
| • | The left rear wheel speed is accelerating or decelerating beyond reasonable limits. |
Action Taken When the DTC Sets
| • | The solenoid relay opens, removing power from the pump motor and solenoids. |
| • | DTC C1207 is stored. |
| • | ABS disabled, ABS warning lamp turns ON. |
Conditions for Clearing the DTC
| • | If the conditions that set the DTC C1207 are no longer present, the DTC may be cleared by using the proper scan tool. |
| • | The DTC that has not occurred in 100 drive cycles will be cleared from history data. |
Diagnostic Aids
Thoroughly inspect the wiring and connectors when diagnosing intermittent DTCs. This will include the following:
| • | Removal of the protective conduit and inspection of wiring for damage, shorts, and contamination |
| • | Inspection for improperly formed and/or damaged terminals |
| • | Checking terminal contact retention force by using a spare male/female terminal |
| • | Removal of the terminals from the connectors to check for proper terminal to wire crimp |
If the driver comments reflect that the ABS warning lamp is ON only during moist environmental changes, such as, rain, snow, vehicle wash, the all wheel speed sensor circuitry should be thoroughly inspected for signs of water intrusion. If the DTC is not current, simulate the effects of water intrusion. Use the following procedure. Spray the suspected area with a 5 percent salt-water solution. Then test-drive the vehicle over various road surfaces such as, bumps, turns, etc., above 24 km/h (15 mph). If the DTC sets then replace the suspected harness and/or sensor.
A careful visual inspection of the wheel speed sensor for damage such as cracks and damage should be performed. If the DTC sets at the same speed every drive cycle, the toothed ring is most likely damaged.
Failure to perform the previous steps carefully and fully can result in misdiagnosis, unnecessary component replacement, and reccurrence of DTC C1207.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Diagnostic System Check - ABS? | -- | Go to Step 2 | |
2 | Was the DTC C1206 set as a current or history DTC? | -- | Go to DTC C1206 | Go to Step 3 |
3 |
Is any physical damage noted? | -- | Go to Step 4 | Go to Step 5 |
4 | Repair the damage to the left rear wheel speed sensor, jumper harness, and/or the toothed ring. Did you find and correct the condition? | -- | System OK | -- |
5 |
Did the DTC C1207 reset or did the left rear wheel speed read above 0 mph when the vehicle was in park with the engine running? | -- | Go to Step 6 | Go to Step 7 |
6 |
Did you find and correct the condition? | -- | System OK | -- |
7 |
Did DTC C1207 reset or did the left rear wheel speed vary more than 5 km/h (3 mph) when compared to any one of the other wheels during the drive? | -- | Go to Step 9 | Go to Step 8 |
8 | DTC C1207 is intermittent. Refer to the Diagnostic System Check - ABS . Did you find and correct the condition? | -- | System OK | -- |
9 |
Is the resistance within the specified range? | 800-1600 ohms | Go to Step 11 | Go to Step 10 |
10 | Replace the left rear wheel speed sensor. Refer to Rear Wheel Speed Sensor Replacement . Did you complete the replacement? | -- | System OK | -- |
11 |
Is the AC voltage greater than the specified value? | 100 mV | Go to Step 12 | Go to Step 10 |
12 |
Is the resistance measured less than the specified value? | 2 ohms | Go to Step 14 | Go to Step 13 |
13 | Repair the source open or high resistance between terminals 5 and 2. Did you find and correct the condition? | -- | System OK | -- |
14 |
Is the resistance measured less than the specified value? | 2 ohms | Go to Step 16 | Go to Step 15 |
15 | Repair the open or high resistance between terminals 6 and 1. Did you find and correct the condition? | -- | System OK | -- |
16 |
Is the resistance within the specified value? | OL (open circuit) | Go to Step 18 | Go to Step 17 |
17 | Repair the short between the 2 wires. Did you find and correct the condition? | -- | System OK | -- |
18 |
Did DTC C1207 reset? | -- | Go to Step 19 | System OK |
19 | Replace the EBCM. Refer to Brake Pressure Modulator Valve Assembly Replacement . Did you complete the replacement? | -- | System OK | -- |
