Circuit Description
The exhaust gas recirculation (EGR) valve position sensor is monitored by the powertrain control module (PCM). The 5-volt reference circuit, low reference circuit and the EGR valve position signal circuit are used by the PCM to determine the EGR valve position. If the EGR valve position sensor signal voltage is more than a calibrated value, DTC P0406 sets.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0406 Exhaust Gas Recirculation (EGR) Position Sensor Circuit High Voltage
Conditions for Running the DTC
| • | DTC P0641 and P0651 are not set. |
| • | The Ignition 1 Signal parameter is more than 11 volts. |
| • | The engine is running. |
| • | The DTC P0401 intrusive test is not active. |
| • | The EGR valve is not being commanded with a scan tool. |
| • | The EGR command will be disabled if the start-up ECT is less than 5°C (41°F) and will not enable until the ECT Sensor parameter is more than 75°C (167°F) |
| • | DTC P0406 runs continuously once the above conditions are met. |
Conditions for Setting the DTC
The EGR Position Sensor parameter is more than 94.7 percent of the 5-volt reference voltage for longer than 4 seconds.
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Engine Controls Connector End Views or Powertrain Control Module Connector End Views | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information |
2 | Is DTC P0641 also set? | -- | Go to DTC P0641 | Go to Step 3 |
3 |
Is the EGR Position Sensor voltage parameter more than the specified value? | 4.4 V | Go to Step 5 | Go to Step 4 |
4 |
Did the DTC fail this ignition? | -- | Go to Step 5 | |
5 |
Is the EGR Position Sensor parameter more then the specified value? | 4.4 V | Go to Step 8 | Go to Step 6 |
6 | Connect a test lamp between the 5-volt reference circuit of the EGR valve and the low reference circuit of the EGR valve. Does the test lamp illuminate? | -- | Go to Step 10 | Go to Step 7 |
7 | Test the low reference circuit of the EGR valve for an open or for high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 9 |
8 | Test the EGR valve position signal circuit for a short to voltage or for a short to the EGR solenoid high control circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 9 |
9 | Test for an intermittent and for a poor connection at the powertrain control module (PCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 12 |
10 | Test for an intermittent and for a poor connection at the EGR valve. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 11 |
11 | Replace the EGR valve. Refer to Exhaust Gas Recirculation Valve Replacement . Did you complete the replacement? | -- | Go to Step 13 | -- |
12 | Replace the PCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 13 | -- |
13 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 14 |
14 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information | System OK |
