Circuit Description
The commanded throttle position is compared to the actual throttle position based on the accelerator pedal position, and possibly other limiting factors. Both values should be within a calibrated range of each other. The powertrain control module (PCM) continuously monitors the commanded and the actual throttle positions. This DTC sets if the values are greater than the calibrated range.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P2101 Control Module Throttle Actuator Position Performance
Conditions for Running the DTC
| • | DTCs P0068, P0120, P0220, P0601, P0604, P0606, P1125, P1516, P2108, P2119, P2120, P2125, P2135, P2138, and U0107 are not set. |
| • | The ignition is in the crank or run position. |
| • | The engine is running or the ignition voltage is more than 8.5 volts. |
| • | The system is not in Battery Saver mode. |
| • | The Ignition 1 Signal parameter is more than 5.23 volts. |
| • | The TAC module determines that the PCM desired throttle position is valid. |
| • | DTC P2101 runs continuously every 18.75 milliseconds once the above conditions are met. |
Conditions for Setting the DTC
The TAC module detects that the commanded and actual throttle positions are not within a calibrated range of each other.
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) when the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Freeze Frame and/or the Failure Records. |
| • | The control module commands the TAC system to operate in the Reduced Engine Power mode. |
| • | A message center or an indicator displays Reduced Engine Power. |
| • | Under certain conditions the control module commands the engine OFF. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Diagnostic Aids
| • | Inspect for mechanical conditions or for binding that may be temperature related. Components may not move freely in extreme heat or cold due to the presence of contaminants or ice formation. |
| • | If the condition is intermittent, refer to Testing for Intermittent Conditions and Poor Connections . |
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Powertrain Control Module Connector End Views and Engine Controls Connector End Views | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |
2 | Is DTC P2108 also set? | -- | Go to Step 3 | |
3 | Is DTC U0107 also set? | -- | Go to Step 4 | |
4 |
Does the TP Sensor 1 and TP Sensor 2 angle increase to near the specified value as the pedal is depressed and decrease as the pedal is released? | 100% | Go to Diagnostic Aids | Go to Step 5 |
5 | Test the ETC ignition 1 voltage circuit for high resistance. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 7 | Go to Step 6 |
6 | Replace the throttle body assembly. Refer to Throttle Body Assembly Replacement . Did you complete the replacement? | -- | Go to Step 7 | -- |
7 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 8 |
8 |
Important: Be aware that repairing 1 individual condition may correct more than 1 DTC. Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | System OK | |
