DTC P0117, P0118, P1114, or P1115. Chevrolet Equinox 2006

For 1990-2009 cars only

Makes 🢒 Chevrolet 🢒 2006 🢒 Equinox 🢒 Vehicle Control Systems 🢒 Vehicle DTC Information 🢒 DTC P0117, P0118, P1114, or P1115

DTC Descriptors

DTC P0117: Engine Coolant Temperature (ECT) Sensor Circuit Low Voltage

DTC P0118 : Engine Coolant Temperature (ECT) Sensor Circuit High Voltage

DTC P1114 : Engine Coolant Temperature (ECT) Sensor Circuit Intermittent Low Voltage

DTC P1115 : Engine Coolant Temperature (ECT) Sensor Circuit Intermittent High Voltage

Diagnostic Fault Information

Important: Always perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

Circuit	Short to Ground	High Resistance	Open	Short to Voltage	Signal Performance
ECT Sensor Signal	P0117	P0118	P0118	P0118	P0116, P0125, P0128
Low Reference	--	P0118	P0118	P0118	P0125, P0128

Typical Scan Tool Data

ECT Sensor Temperatures

Circuit	Normal Range	Short to Ground	Open	Short to Voltage
ECT Sensor Signal	-39°C to +120°C (-38°F to +248°F)	150°C (303°F)	-40°C (-40°F)	-40°C (-40°F)
Low Reference	--	--	-40°C (-40°F)	-40°C (-40°F)

Circuit/System Description

The engine coolant temperature (ECT) sensor is a variable resistor, that measures the temperature of the engine coolant. The control module supplies 5 volts to the ECT signal circuit and a ground for the ECT low reference circuit. When the ECT is cold, the sensor resistance is high. When the ECT increases, the sensor resistance decreases. With high sensor resistance, the control module detects a high voltage on the ECT signal circuit. With lower sensor resistance, the control module detects a lower voltage on the ECT signal circuit.

Conditions for Running the DTC

P0117 or P1114

•	The engine run time is more than 3 seconds.

•	The ignition is ON and the IAT parameter is less than 90°C (194°F).

•	The diagnostic runs continuously when the above conditions are met.

P0118 or P1115

•	The engine is running for more than 30 seconds.

•	The ignition is ON and the IAT parameter is more than 0°C (32°F).

•	The diagnostic runs continuously when the above conditions are met.

Conditions for Setting the DTC

P0117

The control module detects that the ECT sensor parameter is more than 139°C (282°F) for more than 24 seconds.

P0118

The control module detects that the ECT sensor parameter is less than -37°C (-35°F) for more than 24 seconds.

P1114

The control module detects that the ECT sensor parameter is more than 139°C (282°F) intermittently for more than 20 seconds.

P1115

The control module detects that the ECT sensor parameter is less than -37°C (-35°F) intermittently for more than 20 seconds.

Action Taken When the DTC Sets

P0117 and P0118

•	The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.

•

The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.

P1114 and P1115

•	The control module stores the DTC information into memory when the diagnostic runs and fails.

•	The MIL will not illuminate.

•	The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Failure Records.

•	The driver information center, if equipped, may display a message.

Conditions for Clearing the DTC

P0117 or P0118

•	The control module turns OFF the MIL after 3 consecutive ignition cycles that the diagnostic runs and does not fail.

•	A current DTC, Last Test Failed, clears when the diagnostic runs and passes.

•	A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.

•	Clear the MIL and the DTC with a scan tool.

P1114 or P1115

•	A current DTC Last Test Failed clears when the diagnostic runs and passes.

•	A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other non-emission related diagnostic.

•	Clear the DTC with a scan tool.

Diagnostic Aids

•	An overheating condition may cause this DTC to set.

•	After starting the engine, the ECT sensor temperature should rise steadily to about 90°C (194°F) then stabilize after the thermostat opens.

•	If a short to a separate voltage source occurs this DTC may set and damage the ECT sensor.

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

•	Engine Controls Connector End Views

•	Powertrain Control Module Connector End Views

Electrical Information Reference

•	Circuit Testing

•	Connector Repairs

•	Testing for Intermittent Conditions and Poor Connections

•	Wiring Repairs

•	Using Fused Jumper Wires

•	Inducing Intermittent Fault Conditions

Circuit/System Testing

Did you perform the Diagnostic System Check - Vehicle ?

Important:

•	The cooling fans are commanded ON when certain DTCs are set.

•	If a short to voltage occurs, the ECT sensor may be damaged.

P0117

Ignition ON, engine OFF, disconnect the ECT sensor and observe the ECT parameter for -38°C (-36°F).

⇒	If over -38°C (-36°F), test the signal circuit of the ECT sensor for a short to ground or a short to any low reference circuit. If tests OK, then replace the ECT sensor.

⇒	If under -38°C (-36°F), test for an intermittent and for a poor connection at the ECT sensor. If the ECT circuit tests OK, then replace the control module.

P0118

With the ignition ON, engine OFF, disconnect the ECT sensor and measure for 5.2 volts from the signal circuit of the ECT sensor to a good round with a DMM.

⇒	If over 5.2 volts, then test the ECT signal circuit for a short to voltage, for an intermittent and for a poor connection at the control module. If all test OK then replace the control module.

⇒	If under 5.2 volts, then test the signal circuit of the ECT sensor for high resistance or an open, or a short to any 5-volt reference circuit. If tests OK then replace the ECT sensor.

With the ignition ON, engine OFF.
Connect a 3-amp jumper wire between the signal circuit of the ECT sensor and the low reference circuit.
Observe the ECT parameter with a scan tool for 139°C (282°F).

⇒	If more than specified value than, test the ECT signal circuit for a short to any 5-volt reference circuit, or a faulty connection at control module. If circuits test OK then replace the ECT sensor.

Connect a 3-amp jumper wire between the signal circuit of the ECT sensor and a good ground.
Observe the ECT parameter with a scan tool for 139°C (282°F).

⇒	If more than specified value then, test the ECT low reference circuit for high resistance or an open. Test for a faulty connection at the control module, or a faulty control module. If circuit test OK then replace the control module.

P1114 or P1115

Observe the ECT sensor parameter on the scan tool, while moving the ECT sensor connector and the control module connector. Is there an abrupt change indicated on the scan tool.

⇒	If change then repair the connector or terminal as necessary.

⇒	If no change observe the ECT sensor parameter on the scan tool, while moving the wiring harness at the ECT sensor and the control module. If there is a change on the scan tool then repair the wiring as necessary.

If everything tests OK, then go to Testing for Intermittent Conditions and Poor Connections .

Repair Instructions

Important: Always perform the Diagnostic Repair Verification after completing the diagnostic procedure.

•	Engine Coolant Temperature Sensor Replacement

•	Control Module References for PCM replacement, setup, and programming.

Repair Verification

Diagnostic Repair Verification