GM Service Manual Online
For 1990-2009 cars only

Fuel Tank Replacement AWD

Removal Procedure

    Caution: Do not allow smoking or the use of open flames in the area where work on the fuel or EVAP system is taking place. Anytime work is being done on the fuel system, disconnect the negative battery cable, except for those tests where battery voltage is required.

  1. Ensure that the fuel level in the tank is less than 1/4 full. If necessary, drain the fuel tank to at least this level. Refer to Fuel Tank Draining .
  2. Caution: Fuel supply lines will remain pressurized for long periods of time after the engine is shutdown. This pressure must be relieved before servicing the fuel system.

  3. Relieve the fuel system pressure. Refer to Fuel Pressure Relief .
  4. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  5. Raise and support the vehicle . Refer to Lifting and Jacking the Vehicle .
  6. Remove the exhaust system. Refer to Exhaust System Replacement .
  7. Remove the propeller shaft. Refer to Propeller Shaft Replacement .

  8. Object Number: 1371133  Size: SH

    Notice: Clean all fuel pipe connections and surrounding areas before disconnecting the fuel pipes to avoid contamination of the fuel system.

    Caution: Whenever fuel lines are removed, catch fuel in an approved container. Container opening must be a minimum of 300 mm (12  in) diameter to adequately catch the fluid.

  9. Place a suitable container under the fuel line connection in order to catch any dripping fuel.
  10. Disconnect the chassis fuel supply line (2) from the fuel tank.

  11. Object Number: 1347586  Size: SH
  12. Disconnect the fuel filler tube, EVAP vent hose, and fresh air hose from the fuel tank.
  13. Disconnect the fuel tank electrical connector and remove the electrical connector retainer from the rear frame.

  14. Object Number: 927748  Size: SH

    Notice: Do not bend the fuel tank straps. Bending the fuel tank straps may cause damage to the straps.

  15. Support the fuel tank.
  16. Remove the fuel tank strap bolts and fuel tank straps.
  17. Lower the fuel tank (with shield) from the underbody of the vehicle.
  18. If replacing the fuel tank, remove the fuel tank module assemblies. Refer to Primary Fuel Tank Module Replacement and Secondary Fuel Tank Module Replacement .
  19. If replacing the fuel tank, remove the heat shield from the tank.

Installation Procedure

  1. If previously removed, install the fuel tank module assemblies. Refer to Primary Fuel Tank Module Replacement and Secondary Fuel Tank Module Replacement .
  2. If previously removed, install the heat shield to the fuel tank.

  3. Object Number: 927748  Size: SH
  4. Install the fuel tank heat shield and fuel tank assembly to the vehicle.
  5. Notice: Refer to Fastener Notice in the Preface section.

  6. Install the fuel tank straps and the fuel tank strap-to-body bolts.
  7. Tighten
    Tighten the bolts to 25 N·m (18 lb ft).


    Object Number: 1347586  Size: SH
  8. Connect the fuel tank electrical connector and install the electrical connector retainer to the rear frame.
  9. Connect the EVAP vent, and fresh air hoses to the fuel tank.
  10. Connect the fuel filler tube to the fuel tank.
  11. Tighten
    Tighten the fuel filler tube clamp to 5 N·m (44 lb in).


    Object Number: 1371133  Size: SH
  12. Connect the chassis fuel supply line (2) to the fuel tank.
  13. Install the propeller shaft. Refer to Propeller Shaft Replacement .
  14. Install the exhaust system. Refer to Exhaust System Replacement .
  15. Lower the vehicle .
  16. Fill the fuel tank with gasoline.
  17. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  18. Prime the fuel system:
  19. 14.1. Cycle the ignition ON for 5 seconds and then OFF for 10 seconds.
    14.2. Repeat the previous step twice.
    14.3. Crank the engine until it starts. The maximum starter motor cranking time is 20 seconds.
    14.4. If the engine does not start, repeat steps 13.1-13.3.

Fuel Tank Replacement FWD

Removal Procedure

    Caution: Do not allow smoking or the use of open flames in the area where work on the fuel or EVAP system is taking place. Anytime work is being done on the fuel system, disconnect the negative battery cable, except for those tests where battery voltage is required.

  1. Ensure that the fuel level in the tank is less than 1/4 full. If necessary, drain the fuel tank to at least this level. Refer to Fuel Tank Draining .
  2. Caution: Fuel supply lines will remain pressurized for long periods of time after the engine is shutdown. This pressure must be relieved before servicing the fuel system.

  3. Relieve the fuel system pressure. Refer to Fuel Pressure Relief.
  4. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  5. Raise and support the vehicle . Refer to Lifting and Jacking the Vehicle .
  6. Remove the exhaust system. Refer to Exhaust System Replacement .

  7. Object Number: 1371133  Size: SH
  8. Remove the evaporative emission (EVAP) canister (4). Refer to Evaporative Emission Canister Replacement .
  9. Notice: Clean all fuel pipe connections and surrounding areas before disconnecting the fuel pipes to avoid contamination of the fuel system.

    Caution: Whenever fuel lines are removed, catch fuel in an approved container. Container opening must be a minimum of 300 mm (12  in) diameter to adequately catch the fluid.

  10. Disconnect the chassis fuel supply line (2) from the fuel tank.

  11. Object Number: 1347586  Size: SH
  12. Disconnect the fuel filler tube, EVAP vent hose, and fresh air hose from the fuel tank.
  13. Disconnect the fuel tank electrical connector and remove the electrical connector retainer from the rear frame.

  14. Object Number: 927748  Size: SH

    Notice: Do not bend the fuel tank straps. Bending the fuel tank straps may cause damage to the straps.

    Important: Do not lower the rear frame. It is not necessary to lower the rear frame for fuel tank removal.

  15. Support the fuel tank.
  16. Remove the fuel tank strap bolts and fuel tank straps.
  17. Lower the fuel tank from the underbody of the vehicle.
  18. If replacing the fuel tank, remove the fuel tank module assemblies. Refer to Primary Fuel Tank Module Replacement and Secondary Fuel Tank Module Replacement .

Installation Procedure

  1. If previously removed, install the fuel tank module assemblies. Refer to Primary Fuel Tank Module Replacement and Secondary Fuel Tank Module Replacement .

  2. Object Number: 927748  Size: SH
  3. Install the fuel tank heat shield and fuel tank assembly to the vehicle.
  4. Notice: Refer to Fastener Notice in the Preface section.

  5. Install the fuel tank straps and the fuel tank strap-to-body bolts.
  6. Tighten
    Tighten the bolts to 25 N·m (18 lb ft).


    Object Number: 1347586  Size: SH
  7. Connect the fuel tank electrical connector and install the electrical connector retainer to the rear frame.
  8. Connect the EVAP vent, and fresh air hoses to the fuel tank.
  9. Connect the fuel filler tube to the fuel tank.
  10. Tighten
    Tighten the fuel filler tube clamp to 5 N·m (44 lb in).


    Object Number: 1371133  Size: SH
  11. Connect the chassis fuel supply line (2) to the fuel tank.
  12. Install the evaporative emission (EVAP) canister (4). Refer to Evaporative Emission Canister Replacement .
  13. Install the exhaust system. Refer to Exhaust System Replacement .
  14. Lower the vehicle .
  15. Fill the fuel tank with gasoline.
  16. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  17. Prime the fuel system:
  18. 13.1. Cycle the ignition ON for 5 seconds and then OFF for 10 seconds.
    13.2. Repeat the previous step twice.
    13.3. Crank the engine until it starts. The maximum starter motor cranking time is 20 seconds.
    13.4. If the engine does not start, repeat steps 13.1-13.3.