Displays Test
Certain instrument panel cluster (IPC) features are tested when the ignition is turned on in order to verify that the features are working properly. The following indicators illuminate briefly at key up:
| • | Air bag--flashes 7 times |
| • | Engine Coolant Temperature |
| • | Low oil pressure indicator |
| • | Malfunction indicator lamp (MIL)--Check engine |
| • | Reduced Engine Power indicator |
| • | Service Vehicle Soon indicator |
| • | Stability System Disabled |
Indicators and Warning Messages
Refer to
Indicator/Warning Message Description and Operation.
Engine Coolant Temperature Gage
The engine control module (ECM) calculates the engine coolant temperature as determined by the coolant temperature sensor. The ECM sends the engine coolant temperature to the body control module (BCM) via the serial data circuit. The instrument panel cluster
(IPC) displays the engine coolant temperature when the BCM sends a serial data message to the IPC indicating the engine coolant temperature. The engine coolant temperature gage defaults to 0° or below if:
| • | The ECM detects a malfunction in the engine coolant temperature sensor circuit. |
| • | The IPC detects a loss of serial data communications with the BCM. |
| • | The BCM detects a loss of serial data communications with the ECM. |
Fuel Gage
The engine control module (ECM) sends the fuel level percent to the BCM via the serial data circuit. The IPC displays the fuel level as received from the BCM. The fuel gage defaults to E (empty) if:
| • | The ECM detects a malfunction in the fuel level sensor circuit. |
| • | The IPC detects a loss of serial data communications with the BCM. |
| • | The BCM detects a loss of serial data communications with the ECM. |
When the fuel level is less than a pre-determined value, the Low Fuel indicator message illuminates.
Odometer
The odometer shows how far the vehicle has been driven, in either miles (domestic) or kilometers (export). The odometer is shown on display when any of the following occur:
| • | Ignition is in RUN, with no messages on |
| • | The trip reset stem is pressed with the ignition OFF |
Odometer readings are displayed in the IPC based on serial data message from the BCM. The ECM calculates the distance traveled from the vehicle speed sensor (VSS) input. The BCM receives a serial data message from the PCM and stores the current mileage.
The IPC stores the last valid odometer reading from the BCM in non-volatile memory. When a new valid odometer reading is received from the BCM, the IPC will update the display and store the new reading.
The IPC also receives serial data messages from the BCM regarding VIN and Vehicle content information. Valid information is stored in non-volatile memory at the first key-up with a new IPC. If the VIN or option content do not match the stored information,
the odometer will display ERROR.
Speedometer
The IPC displays the vehicle speed based on the information from the BCM. The ECM calculates the vehicle speed based on the vehicle speed sensor (VSS) input. The ECM sends a serial data message to the BCM indicating the vehicle speed. The BCM sends a serial
data message to the IPC indicating the vehicle speed.
The speedometer defaults to 0 km/h (0 mph) when any of the following occur:
| • | The EBCM detects a malfunction in the vehicle speed sensor circuit. |
| • | The PCM detects a loss of serial data communications with the EBCM. |
| • | The BCM detects a loss of serial data communications with the PCM. |
| • | The IPC detects a loss of serial data communications with the BCM. |
Tachometer
The IPC displays the engine speed as determined by the ECM. The ECM determines the engine speed and sends a serial data message to the BCM indicating the engine speed. The tachometer will default to 0 RPM if:
| • | The ECM detects a malfunction in the engine speed sensor circuit. |
| • | The BCM detects a loss of serial data communications with the ECM. |
| • | The IPC detects a loss of serial data communications with the BCM. |
Trip Odometer
Trip odometer readings are calculated by the IPC based on the odometer reading received through a serial data message from the BCM. The trip odometer is shown when selected with the odometer trip reset stem. To reset the trip odometer, press and hold the
trip reset stem for about two seconds, until the trip odometer shows zero.
