| Table 1: | Front Compartment |
| Table 2: | Body Side |
| Table 3: | Underbody |
Three Dimensional Distance -- X, Y, Z
This universal measuring system is capable of simultaneously dimensioning the length, width, and height of a datum plane. Three dimensional distances are used for both underbody and upperbody measuring.
X = Fore and aft measurements along the center line of the vehicle. An O plane is located forward of the master gage hole at the front of the vehicle 2185 mm as shown. All measurements are made from this plane toward the rear of the vehicle.
Y = Cross car dimensions. Positive values are measured from the center of the vehicle to the right side of the vehicle. Negative values are measured from the center of the vehicle to the left side. When values are not listed separately to change the side of the vehicle, you need only to change the Y dimensions to the opposite value, + or -, from what is listed.
Z = Vertical measurement from the datum plane that is 368 mm below the rocker panel lower flange edge (O plane).
All dimensions are symmetrical, unless otherwise noted.
In order to properly repair the spaceframe, restore the vehicle to the XYZ dimensions, as originally built. Relational (linear) dimensions are for reference only. Use relational dimensions for diagnosis or inspection only. Relational dimensions are not as accurate as XYZ dimensions and measuring systems.
The gage holes shown are the actual fixture locations that are used to build the vehicle.
Front Compartment
Location | Description | Length = x | Width = y | Height = z | Point to Point |
|---|---|---|---|---|---|
1 | Hole | 1100 | 314 | 879 | x |
2 | Hole | 1225 | 689 | 889 | x |
3 | Strut Attachment Hole | 1648 | 544 | 934 | x |
4 | Hood Hinge Hole | 1829 | 714 | 982 | x |
5 | Hood Hinge Hole | 1930 | 714 | 993 | x |
6 | Air Inlet Grille Attachment Hole | 1849 | 600 | 975 | x |
7 | Strut Attachment Hole | 1648 | -544 | 934 | x |
8 | Air Inlet Grille Attachment Hole | 1813 | -616 | 975 | x |
9 | Hood Hinge Hole | 1829 | -714 | 982 | x |
10 | Hood Hinge Hole | 1930 | -714 | 993 | x |
11 | Hole | 1225 | -689 | 889 | x |
12 | Hole | 1100 | -314 | 879 | x |
13 | Hood Striker Attachment Hole | 1080 | -83 | 869 | x |
14 | Hood Striker Attachment Hole | 1018 | 1 | 852 | x |
15 | Impact Bar Attachment Hole | 946 | 574 | 480 | x |
16 | Impact Bar Attachment Hole | 924 | 396 | 480 | x |
17 | Impact Bar Attachment Hole | 946 | 574 | 405 | x |
18 | Impact Bar Attachment Hole | 924 | 396 | 405 | x |
19 | Impact Bar Attachment Hole | 924 | -396 | 480 | x |
20 | Impact Bar Attachment Hole | 946 | -396 | 480 | x |
21 | Impact Bar Attachment Hole | 924 | -574 | 405 | x |
22 | Impact Bar Attachment Hole | 946 | -574 | 405 | x |
15 to 20 | x | x | x | x | 1143 |
18 to 21 | x | x | x | x | 787 |
2 to 11 | x | x | x | x | 1380 |
4 to 11 | x | x | x | x | 1522 |
2 to 9 | x | x | x | x | 1525 |
All dimensions are measured from a zero line, a center line, and a common datum. All dimensions are symmetrical unless otherwise specified. | |||||
Body Side
Location | Length |
|---|---|
a-g | 711 mm |
a-i | 1620 mm |
b-f | 1056 mm |
b-e | 1167 mm |
b-c | 377 mm |
c-e | 1073 mm |
c-f | 1116 mm |
d-h | 2102 mm |
e-f | 432 mm |
e-i | 831 mm |
f-h | 1410 mm |
Underbody
Location | Description | Length = x | Width = y | Height = z | Point to Point |
|---|---|---|---|---|---|
a | Hole | 979 | -486 | 342 | x |
b | Hole | 1261 | -474 | 287 | x |
c | Hole | 2081 | -382 | 230 | x |
d | Hole | 2192 | -600 | 192 | x |
f | Hole | 3688 | -466 | 205 | x |
g | Hole | 5100 | -475 | 354 | x |
h | Hole | 5100 | 475 | 354 | x |
i | Hole | 3688 | 466 | 205 | x |
k | Hole | 2192 | 600 | 192 | x |
l | Hole | 2081 | 382 | 230 | x |
m | Hole | 1261 | 474 | 287 | x |
n | Hole | 979 | 486 | 342 | x |
a to g | x | x | x | x | 4128 mm |
a to e | x | x | x | x | 1288 mm |
a to j | x | x | x | x | 1568 mm |
b to l | x | x | x | x | 1185 mm |
c to m | x | x | x | x | 1185 mm |
d to f | x | x | x | x | 1502 mm |
d to i | x | x | x | x | 1837 mm |
e to i | x | x | x | x | 1585 mm |
e to n | x | x | x | x | 1568 mm |
f to g | x | x | x | x | 1419 mm |
f to j | x | x | x | x | 1585 mm |
f to k | x | x | x | x | 1837 mm |
f to h | x | x | x | x | 1703 mm |
g to i | x | x | x | x | 1703 mm |
h to i | x | x | x | x | 1419 mm |
h to n | x | x | x | x | 4128 mm |
i to k | x | x | x | x | 1502 mm |
j to n | x | x | x | x | 1288 mm |
