GM Service Manual Online
For 1990-2009 cars only

Brake Pressure Modulator Valve Replacement With JL4

Removal Procedure

Warning: Refer to Brake Fluid Irritant Warning in the Preface section.

Caution: Refer to Brake Fluid Effects on Paint and Electrical Components Caution in the Preface section.

  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
  2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
  3. Remove the 2 brake modulator shield mounting nuts, if equipped.
  4. Remove the brake modulator shield mounting bolt and the shield.
  5. Remove all dirt and debris from the electronic brake control module (EBCM) and the brake pressure modulator valve (BPMV) before loosening or removing any of the components.
  6. Disconnect the electrical connector from the EBCM.
  7. If equipped with AWD, remove the LF suspension torsion bar. Refer to Torsion Bar and Support Assembly Replacement.

  8. Object Number: 2001465  Size: SH
  9. Disconnect the rear master cylinder brake pipe fitting (1).
  10. Cap the brake pipe fitting and plug the BPMV inlet port to prevent brake fluid loss and contamination.


    Object Number: 2001466  Size: SH
  11. Disconnect the front master cylinder brake pipe fitting (1).
  12. Cap the brake pipe fitting and plug the BPMV inlet port to prevent brake fluid loss and contamination.


    Object Number: 2001469  Size: SH
  13. Disconnect the LF brake pipe fitting (1).
  14. Cap the brake pipe fitting and plug the BPMV outlet port to prevent brake fluid loss and contamination.


    Object Number: 2001471  Size: SH
  15. Disconnect the RF brake pipe fitting (1).
  16. Cap the brake pipe fitting and plug the BPMV outlet port to prevent brake fluid loss and contamination.


    Object Number: 2001474  Size: SH
  17. Disconnect the LR brake pipe fitting (1).
  18. Cap the brake pipe fitting and plug the BPMV outlet port to prevent brake fluid loss and contamination.


    Object Number: 2001477  Size: SH
  19. Disconnect the RR brake pipe fitting (1).
  20. Cap the brake pipe fitting and plug the BPMV outlet port to prevent brake fluid loss and contamination.


    Object Number: 2001479  Size: SH
  21. Remove the BPMV bracket bolts (1).
  22. Remove the BPMV and bracket assembly from the vehicle.

  23. Object Number: 2001482  Size: SH
  24. Remove the BPMV bolt (1).

  25. Object Number: 2001484  Size: SH
  26. Remove the BPMV assembly (1) from the bracket.
  27. If installing a new BPMV, remove the EBCM. Refer to Electronic Brake Control Module Replacement.

Installation Procedure


    Object Number: 2001484  Size: SH
  1. Install the EBCM, if removed. Refer to Electronic Brake Control Module Replacement.
  2. Install the BPMV assembly (1) to the bracket.
  3. Caution: Refer to Fastener Caution in the Preface section.


    Object Number: 2001482  Size: SH
  4. Install the BPMV bolt (1) and tighten to  11 N·m (97 lb in).

  5. Object Number: 2001479  Size: SH
  6. Install the BPMV and bracket assembly to the vehicle.
  7. Install the BPMV bracket bolts (1) and tighten to  25 N·m (18 lb ft).

  8. Object Number: 2001477  Size: SH
  9. Connect the RR brake pipe fitting (1) and tighten to  25 N·m (18 lb ft).

  10. Object Number: 2001474  Size: SH
  11. Connect the LR brake pipe fitting (1) and tighten to  25 N·m (18 lb ft).

  12. Object Number: 2001471  Size: SH
  13. Connect the RF brake pipe fitting (1) and tighten to  25 N·m (18 lb ft).

  14. Object Number: 2001469  Size: SH
  15. Connect the LF brake pipe fitting (1) and tighten to  25 N·m (18 lb ft).

  16. Object Number: 2001466  Size: SH
  17. Connect the front master cylinder brake pipe fitting (1) and tighten to  25 N·m (18 lb ft).

  18. Object Number: 2001465  Size: SH
  19. Connect the rear master cylinder brake pipe fitting (1) and tighten to  25 N·m (18 lb ft).
  20. Install the brake modulator shield, if equipped.
  21. Install the brake modulator shield bolt and tighten to  25 N·m (18 lb ft).
  22. Install the 2 brake modulator shield nuts and tighten to  25 N·m (18 lb ft).
  23. If equipped with AWD, install the LF suspension torsion bar. Refer to Torsion Bar and Support Assembly Replacement.
  24. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
  25. Bleed the antilock brake system. Refer to Antilock Brake System Automated Bleed Procedure.

Brake Pressure Modulator Valve Replacement Without JL4

Removal Procedure

Warning: Refer to Brake Fluid Irritant Warning in the Preface section.

Caution: Refer to Brake Fluid Effects on Paint and Electrical Components Caution in the Preface section.

  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
  2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
  3. Remove the 2 brake modulator shield mounting nuts, if equipped.
  4. Remove the brake modulator shield bolt and the brake modulator shield.
  5. Remove all dirt and debris from the electronic brake control module (EBCM) and the brake pressure modulator valve (BPMV) before loosening or removing any of the components.
  6. Disconnect the electrical connector from the EBCM.
  7. If equipped with AWD, remove the LF suspension torsion bar. Refer to Torsion Bar and Support Assembly Replacement.

  8. Object Number: 2001485  Size: SH
  9. Disconnect the front master cylinder brake pipe fitting (1).
  10. Cap the brake pipe fitting and plug the BPMV inlet port to prevent brake fluid loss and contamination.


    Object Number: 2001487  Size: SH
  11. Disconnect the rear master cylinder brake pipe fitting (1).
  12. Cap the brake pipe fitting and plug the BPMV inlet port to prevent brake fluid loss and contamination.


    Object Number: 2001488  Size: SH
  13. Disconnect the rear brake pipe fitting (1).
  14. Cap the brake pipe fitting and plug the BPMV outlet port to prevent brake fluid loss and contamination.


    Object Number: 2001489  Size: SH
  15. Disconnect the RF brake pipe fitting (1).
  16. Cap the brake pipe fitting and plug the BPMV outlet port to prevent brake fluid loss and contamination.


    Object Number: 2001492  Size: SH
  17. Disconnect the LF brake pipe fitting (1).
  18. Cap the brake pipe fitting and plug the BPMV outlet port to prevent brake fluid loss and contamination.


    Object Number: 2001494  Size: SH
  19. Remove the BPMV bracket bolts (1).
  20. Remove the BPMV and bracket assembly from the vehicle.

  21. Object Number: 2001495  Size: SH
  22. Remove the BPMV bolt (1).

  23. Object Number: 2001484  Size: SH
  24. Remove the BPMV assembly (1) from the bracket.
  25. If installing a new BPMV, remove the EBCM. Refer to Electronic Brake Control Module Replacement.

Installation Procedure


    Object Number: 2001484  Size: SH
  1. Install the EBCM to the BPMV, if removed. Refer to Electronic Brake Control Module Replacement.
  2. Install the BPMV assembly (1) to the bracket.
  3. Caution: Refer to Fastener Caution in the Preface section.


    Object Number: 2001495  Size: SH
  4. Install the BPMV bolt (1) and tighten to  11 N·m (97 lb in).

  5. Object Number: 2001494  Size: SH
  6. Install the BPMV and bracket assembly to the vehicle.
  7. Install the BPMV bracket bolts (1) and tighten to  25 N·m (18 lb ft).

  8. Object Number: 2001492  Size: SH
  9. Connect the LF brake pipe fitting (1) and tighten to  25 N·m (18 lb ft).

  10. Object Number: 2001489  Size: SH
  11. Connect the RF brake pipe fitting (1) and tighten to  25 N·m (18 lb ft).

  12. Object Number: 2001488  Size: SH
  13. Connect the rear brake pipe fitting (1) and tighten to  25 N·m (18 lb ft).

  14. Object Number: 2001487  Size: SH
  15. Connect the rear master cylinder brake pipe fitting (1) and tighten to  25 N·m (18 lb ft).

  16. Object Number: 2001485  Size: SH
  17. Connect the front master cylinder brake pipe fitting (1) and tighten to  25 N·m (18 lb ft).
  18. Install the brake modulator shield, if equipped.
  19. Install the brake modulator shield nuts and tighten to  25 N·m (18 lb ft).
  20. Install the brake modulator shield bolt and tighten to  25 N·m (18 lb ft).
  21. If equipped with AWD, install the LF suspension torsion bar. Refer to Torsion Bar and Support Assembly Replacement.
  22. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
  23. Bleed the antilock brake system. Refer to Antilock Brake System Automated Bleed Procedure.