GM Service Manual Online
For 1990-2009 cars only

DTC P0563 ECM

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC P0563 : System Voltage High

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

IGN I

P0562

P0562

--

--

Ground

--

P0562

--

--

Circuit/System Description

The engine control module (ECM) monitors the system voltage to ensure that the voltage stays within the proper range. Damage to components, and incorrect data may occur when the voltage is out of range.

Conditions for Running the DTC

    • The vehicle speed is above 8 km/h (5 mph).
    • The system voltage is between 9.5-18 V.

Conditions for Setting the DTC

The ECM detects a system voltage above 16 V.

Action Taken When the DTC Sets

DTC P0563 is a C type DTC.

Conditions for Clearing the DTC

DTC P0563 is a C type DTC.

Diagnostic Aids

    • A possible cause of this DTC could be overcharging with a battery charger or jump starting.
    • A high voltage value in multiple modules indicates a concern in the charging system.

Reference Information

Schematic Reference

    •  Engine Controls Schematics for the 4.3L engine.
    •  Engine Controls Schematics for V8 gas engines.
    •  Engine Controls Schematics for the 6.6L engine.

Connector End View Reference

Component Connector End Views

Description and Operation

Charging System Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

  1. Verify DTC P0563 is set as current.
  2. Engine running measure and record the voltage at the battery terminals. Verify that the battery voltage is 12.6-15.5 V.
  3. If the battery voltage is not within the specified range, refer to Charging System Test.
  4. Engine running, observe the scan tool ECM Ignition 1 signal parameter.
  5. Verify the battery and Ignition 1 signal readings do not differ more than 2.0 V.
  6. If greater than specified value, replace the ECM.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

Control Module References for ECM replacement, setup, and programming.

DTC P0563 FSCM

Diagnostic Instructions

    •  Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    •  Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC P0563: System Voltage High - FPCM

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

B+

P0562

P0562

--

--

Ground

--

P0562

--

--

Circuit/System Description

The fuel pump control module (FPCM) monitors the system voltage to ensure that the voltage stays within the proper range. Damage to components, and incorrect data may occur when the voltage is out of range. If the FPCM detects that the system voltage is high, DTC P0563 sets.

Conditions for Running the DTC

The ignition is ON.

Conditions for Setting the DTC

The FPCM detects that the system voltage is greater than 18 V.

Action Taken When the DTC Sets

DTC P0563 is a type C DTC.

Conditions for Clearing the DTC

DTC P0563 is a type C DTC.

Diagnostic Aids

    • A high voltage DTC in multiple modules indicates a concern in the charging system.
    • This DTC could be set by overcharging with a battery charger or jump starting.

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Charging System Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

  1. Engine running, accessories OFF, measure and record the battery voltage at the battery terminals. The voltage should be between 12.6 and 15.0 V.
  2. If not within the specified range, refer to Charging System Test.
  3. If all circuits test normal, replace the FPCM.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

Control Module References for FPCM replacement, setup, and programming.