GM Service Manual Online
For 1990-2009 cars only

Air Conditioning (A/C) Compressor and Power Steering Pump Bracket Replacement LLY, LBZ

Removal Procedure


    Object Number: 1733035  Size: SH
  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  2. Remove the drive belt. Refer to Drive Belt Replacement .
  3. Remove the auxiliary generator, if equipped. Refer to Auxiliary Generator Replacement .
  4. Remove the auxiliary generator bracket bolt and bracket, if equipped.
  5. Remove the auxiliary generator idler pulley, if equipped.

  6. Object Number: 1733167  Size: SH
  7. Disconnect the engine harness electrical connectors from the air conditioning (A/C) compressor.
  8. Remove the A/C compressor bolts.
  9. Reposition and secure the A/C compressor with the hoses attached out of the way.

  10. Object Number: 1656176  Size: SH
  11. Remove the front power steering pump bracket bolts (1).

  12. Object Number: 1656177  Size: SH
  13. Remove the rear power steering pump bracket bolts (1).
  14. Reposition and secure the power steering pump out of the way.

  15. Object Number: 1733036  Size: SH
  16. Remove the A/C compressor and power steering pump bracket bolts and bracket.

Installation Procedure


    Object Number: 1733036  Size: SH
  1. Position the A/C compressor and power steering pump bracket.
  2. Notice: Refer to Fastener Notice in the Preface section.

  3. Install the A/C compressor and power steering pump bracket bolts.
  4. Tighten
    Tighten the bolts to 46 N·m (34 lb ft).


    Object Number: 1656176  Size: SH
  5. Position the power steering pump and loosely install the front bracket bolts (1).

  6. Object Number: 1656177  Size: SH

    Important: Tighten the front bracket bolts before the rear bracket bolts to ensure pulley alignment.

  7. Loosely install the rear power steering pump bracket bolts (1).
  8. Tighten

    1. Tighten the front bolts to 50 N·m (37 lb ft).
    2. Tighten the rear bolts to 50 N·m (37 lb ft).

    Object Number: 1733167  Size: SH
  9. Position the A/C compressor.
  10. Install the A/C compressor bolts.
  11. Tighten
    Tighten the bolts to 50 N·m (37 lb ft).

  12. Connect the engine harness electrical connectors to the A/C compressor.

  13. Object Number: 1733035  Size: SH
  14. Install the auxiliary generator idler pulley, if equipped.
  15. Tighten
    Tighten the bolt to 50 N·m (37 lb ft)

  16. Install the auxiliary generator bracket bolt and bracket, if equipped.
  17. Tighten
    Tighten the bolt to 50 N·m (37 lb ft)

  18. Install the auxiliary generator, if equipped. Refer to Auxiliary Generator Replacement .
  19. Install the drive belt. Refer to Drive Belt Replacement .
  20. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .

Air Conditioning (A/C) Compressor and Power Steering Pump Bracket Replacement LMM

Removal Procedure


    Object Number: 1733035  Size: SH
  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  2. Remove the drive belt. Refer to Drive Belt Replacement .
  3. Remove the auxiliary generator, if equipped. Refer to Auxiliary Generator Replacement .
  4. Remove the auxiliary generator bracket bolt and bracket, if equipped.
  5. Remove the auxiliary generator idler pulley, if equipped.

  6. Object Number: 1733167  Size: SH
  7. Disconnect the engine harness electrical connectors from the air conditioning (A/C) compressor.
  8. Remove the A/C compressor bolts.
  9. Reposition and secure the A/C compressor with the hoses attached out of the way.

  10. Object Number: 1999493  Size: SH
  11. Remove the cooling fan. Refer to Fan Replacement .
  12. Remove three front power steering pump bracket bolts (1).

  13. Object Number: 1656177  Size: SH
  14. Remove the rear power steering pump bracket bolts (1).
  15. Reposition and secure the power steering pump out of the way.

  16. Object Number: 1733036  Size: SH
  17. Remove the A/C compressor and power steering pump bracket nuts/bolts and bracket.

Installation Procedure


    Object Number: 1733036  Size: SH
  1. Position the A/C compressor and power steering pump bracket.
  2. Notice: Refer to Fastener Notice in the Preface section.

  3. Install the A/C compressor and power steering pump bracket nuts/bolts.
  4. Tighten
    Tighten the bolts to 46 N·m (34 lb ft).


    Object Number: 1999493  Size: SH
  5. Position the power steering pump and loosely install the three front bracket bolts (1).
  6. Install the cooling fan. Refer to Fan Replacement .

  7. Object Number: 1656177  Size: SH

    Important: Tighten the front bracket bolts before the rear bracket bolts to ensure pulley alignment.

  8. Loosely install the rear power steering pump bracket bolts (1).
  9. Tighten

    1. Tighten the front bolts to 50 N·m (37 lb ft).
    2. Tighten the rear bolts to 50 N·m (37 lb ft).

    Object Number: 1733167  Size: SH
  10. Position the A/C compressor.
  11. Install the A/C compressor bolts.
  12. Tighten
    Tighten the bolts to 50 N·m (37 lb ft).

  13. Connect the engine harness electrical connectors to the A/C compressor.

  14. Object Number: 1733035  Size: SH
  15. Install the auxiliary generator idler pulley, if equipped.
  16. Tighten
    Tighten the bolt to 50 N·m (37 lb ft).

  17. Install the auxiliary generator bracket bolt and bracket, if equipped.
  18. Tighten
    Tighten the bolt to 50 N·m (37 lb ft).

  19. Install the auxiliary generator, if equipped. Refer to Auxiliary Generator Replacement .
  20. Install the drive belt. Refer to Drive Belt Replacement .
  21. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .