Center Intake Manifold Replacement LLY, LBZ

1. Remove the turbocharger. Refer to Turbocharger Replacement .
2. Loosen the connector bracket bolt and nut.
3. Remove the connector bracket bolt (1).
4. Remove the fuel rail clamp bolt (2).



5. Remove the connector bracket bolt (2) and nut (1), and reposition the bracket.



6. Disconnect the engine wiring harness electrical connector from the intake air temperature (IAT) sensor No. 2. Refer to Intake Air Temperature (IAT) Sensor 2 Replacement .
7. Remove the center intake manifold 4 bolts (1).
8. Remove the center intake manifold 2 nuts (2) and 2 bolts.
9. Remove the center intake manifold.
10. Remove and discard the center intake manifold gaskets.
11. If replacing the center intake manifold, remove the IAT sensor.

Notice: Refer to Fastener Notice in the Preface section.




1. If the center intake manifold was replaced, install the IAT sensor No. 2.

Tighten
Tighten the sensor to 25 N·m (18 lb ft).

2. Install NEW center intake manifold gaskets to the intake.
3. Install the center intake manifold.

Important: The center intake manifold lower nuts MUST be installed and tightened first.

4. Install the center intake manifold lower 2 nuts (2) and 2 bolts.

Tighten
Tighten the nuts to 10 N·m (89 lb in).

5. Install the center intake manifold upper 4 bolts (1).

Tighten
Tighten the bolts to 10 N·m (89 lb in).

6. Connect the engine wiring harness electrical connector to the IAT sensor No. 2. Refer to Intake Air Temperature (IAT) Sensor 2 Replacement .



7. Position the connector bracket and install the bolt (2) and nut (1).

Tighten
Tighten the bolts to 15 N·m (11 lb ft).




8. Install the fuel rail clamp bolt (2).

Tighten
Tighten the bolt to 25 N·m (18 lb ft).

9. Install the connector bracket bolt (1).

Tighten
Tighten the bolts to 15 N·m (11 lb ft).

10. Install the turbocharger. Refer to Turbocharger Replacement .

Center Intake Manifold Replacement LMM

1. Remove the turbocharger. Refer to Turbocharger Replacement .
2. Loosen the connector bracket bolt and nut.
3. Remove the connector bracket bolt (1).
4. Remove the fuel rail clamp bolt (2).



5. Remove the connector bracket bolt (2) and nut (1), and reposition the bracket.



6. Disconnect the engine wiring harness electrical connector from the intake air temperature (IAT) sensor No. 2. Refer to Intake Air Temperature (IAT) Sensor 2 Replacement .
7. Remove the center intake manifold 4 bolts (1).
8. Remove the center intake manifold 2 nuts (2) and 2 bolts.
9. Remove the center intake manifold.
10. Remove and discard the center intake manifold gaskets.
11. If replacing the center intake manifold, remove the IAT sensor.

Notice: Refer to Fastener Notice in the Preface section.




1. If the center intake manifold was replaced, install the IAT sensor No. 2.

Tighten
Tighten the sensor to 25 N·m (18 lb ft).

2. Install NEW center intake manifold gaskets to the intake.
3. Install the center intake manifold.

Important: The center intake manifold lower nuts MUST be installed and tightened first.

4. Install the center intake manifold lower 2 nuts (2) and 2 bolts.

Tighten
Tighten the nuts to 10 N·m (89 lb in).

5. Install the center intake manifold upper 4 bolts (1).

Tighten
Tighten the bolts to 10 N·m (89 lb in).

6. Connect the engine wiring harness electrical connector to the IAT sensor No. 2. Refer to Intake Air Temperature (IAT) Sensor 2 Replacement.



7. Position the connector bracket and install the bolt (2) and nut (1).

Tighten
Tighten the bolts to 15 N·m (11 lb ft).




8. Install the fuel rail clamp bolt (2).

Tighten
Tighten the bolt to 25 N·m (18 lb ft).

9. Install the connector bracket bolt (1).

Tighten
Tighten the bolts to 15 N·m (11 lb ft).

10. Install the turbocharger. Refer to Turbocharger Replacement .