GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2007 🢒 Express - AWD 🢒 Transmission/Transaxle 🢒 Automatic Transmission - 4L80-E/4L85-E 🢒 Tow/Haul Switch/Indicator Always On or Inoperative

Object Number: 1455734 Size: MF
Master Electrical Component List
Automatic Transmission Controls Schematics (4.8L and 6.0L)
Automatic Transmission Controls Schematics (6.6L)
OBD II Symbol Description Notice
Control Module References

Circuit Description

Tow/haul mode enables the operator to achieve enhanced shift performance when towing or hauling a load. When tow/haul mode is selected, the tow/haul switch input signal to the body control module (BCM) is momentarily toggled to zero volts. This signals the powertrain control module (PCM) or the transmission control module (TCM) to extend the length of time between upshifts and increase transmission line pressure. Cycling the tow/haul switch again disables tow/haul mode and returns the transmission to a normal shift pattern.

Diagnostic Aids

If the electrical circuit checks are OK and the tow/haul shift pattern is not occurring, there may be a mechanical/hydraulic condition that prevents tow/haul operation. Refer to Symptoms - Automatic Transmission .

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. This step tests for a faulty tow/haul switch.

    2.

  2. This step tests for voltage input from the BCM to the tow/haul switch.

    3.

  3. This step tests for ground integrity.

Step

Action

Yes

No

1
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Cycle the tow/haul switch while observing Tow/Haul Mode on the scan tool.

Does the scan tool display Active when the switch is first pressed, and then Inactive when the switch is pressed again?

Go to Testing for Intermittent Conditions and Poor Connections

Go to Step 2

2

  1. Remove the connector from the tow/haul switch.
  2. Using the J 35616 GM terminal test kit, install a fused jumper wire from terminal D to terminal A of the tow/haul switch connector.

Does the scan tool Tow/Haul Mode indicate a status change?

Go to Step 7

Go to Step 3

3

Using the DMM and the J 35616 , measure the voltage at terminal D of the tow/haul switch connector.

Is ignition voltage measured?

Go to Step 6

Go to Step 4

4

Using the DMM and the J 35616 , measure the voltage at terminal C3-B11 of the BCM.

Is ignition voltage measured?

Go to Step 5

Go to Step 8

5

Test the Tow/Haul switch signal circuit of the tow/haul switch for an open or shorted condition. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 9

Go to Testing for Intermittent Conditions and Poor Connections

6

Test the ground circuit of the tow/haul switch for an open or shorted condition. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 9

Go to Testing for Intermittent Conditions and Poor Connections

7

Replace the tow/haul switch. Refer to Instrument Panel Cluster Trim Plate Bezel Replacement.

Did you complete the replacement?

Go to Step 9

--

8

Test the BCM for proper operation. Refer to Diagnostic System Check - Vehicle .

Did you find and correct the condition?

Go to Step 9

--

9

After the repair is complete, observe Tow/Haul Mode on the scan tool display, while cycling the tow/haul switch.

Does the scan tool display Active when the switch is first pressed, and then Inactive when the switch is pressed again?

System OK

Go to Step 1