GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2007 🢒 Express - AWD 🢒 Body Hardware and Trim 🢒 Instrument Panel and Console Trim 🢒 Instrument Panel Carrier Replacement

Removal Procedure

    Caution: Refer to SIR Caution in the Preface section.

    Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

  1. Disconnect the battery negative cable(s). Refer to Battery Negative Cable Disconnection and Connection .
  2. Remove the right knee bolster. Refer to Passenger Knee Bolster Replacement .
  3. Remove the body control module (BCM). Refer to Body Control Module Replacement .
  4. Disable the SIR system. Refer to SIR Disabling and Enabling .
  5. Remove the left knee bolster. Refer to Driver Knee Bolster Replacement .
  6. Remove the left knee bolster bracket. Refer to Driver Knee Bolster Bracket Replacement .
  7. Remove the steering column. Refer to Steering Column Replacement .
  8. Remove the instrument panel (I/P) cluster trim plate bezel. Refer to Instrument Panel Cluster Trim Plate Bezel Replacement .
  9. Remove the instrument cluster assembly. Refer to Instrument Cluster Replacement .
  10. Remove the left hinge pillar trim panel. Refer to Body Hinge Pillar Trim Panel Replacement .
  11. Remove the right hinge pillar trim panel. Refer to Body Hinge Pillar Trim Panel Replacement .
  12. Remove the right knee bolster bracket. Refer to Passenger Knee Bolster Bracket Replacement .
  13. Remove the passenger side SIR module. Refer to Inflatable Restraint Instrument Panel Module Replacement .
  14. Remove the I/P upper trim pad. Refer to Instrument Panel Upper Trim Pad Replacement .
  15. Remove the engine cover. Refer to Engine Cover Replacement .
  16. Remove the radio and mounting bracket, if equipped. Refer to Radio Replacement .
  17. Remove the I/P compartment, if equipped. Refer to Instrument Panel Compartment Replacement .
  18. Remove the heater and the A/C control. Refer to Heater and Air Conditioning Control Replacement .
  19. Remove the steering column wiring harness from the instrument panel carrier.
  20. Remove the bolts that retain the I/P carrier to the vehicle.
  21. Rotate the I/P carrier out and downward in order to gain access to the HVAC ducts and the electrical harness.

    22. Object Number: 301649 Size: SH
  22. Remove the bolts that retain the air ducts to the I/P carrier.
  23. Remove the HVAC air distribution duct from the I/P carrier. Refer to Air Distributor Duct Replacement .
  24. Remove the wiring harness from the I/P carrier.

    25. Object Number: 328139 Size: SH
  25. Remove the I/P carrier from the vehicle.

Installation Procedure

    Object Number: 328139 Size: SH
  1. Install the I/P carrier to the vehicle.
  2. Install the wiring harness to the I/P carrier.

    3. Object Number: 301649 Size: SH
  3. Install the HVAC air distribution duct to the I/P carrier. Refer to Air Distributor Duct Replacement .
  4. Carefully rotate the I/P carrier up to install the additional components.

    5. Notice: Refer to Fastener Notice in the Preface section.

  5. Install the bolts that retain the I/P carrier to the vehicle.

    6. Tighten
    Tighten the bolts to 50 N·m (37 lb ft).

  6. Install the instrument cluster wiring harness to the I/P carrier.
  7. Install the steering column wiring harness to the I/P carrier.
  8. Install the radio, the heater, and the A/C wiring harnesses to the I/P carrier.
  9. Install the heater and the A/C control. Refer to Heater and Air Conditioning Control Replacement .
  10. Install the I/P compartment, if equipped. Refer to Instrument Panel Compartment Replacement .
  11. Install the mounting bracket and radio , if equipped. Refer to Radio Replacement .
  12. Install the engine cover. Refer to Engine Cover Replacement .
  13. Install the I/P upper trim pad. Refer to Instrument Panel Upper Trim Pad Replacement .
  14. Install the passenger side SIR module. Refer to Inflatable Restraint Instrument Panel Module Replacement .
  15. Install the right hinge pillar trim panel. Refer to Body Hinge Pillar Trim Panel Replacement .
  16. Install the left hinge pillar trim panel. Refer to Body Hinge Pillar Trim Panel Replacement .
  17. Install the instrument cluster assembly. Refer to Instrument Cluster Replacement .
  18. Install the I/P cluster trim plate bezel. Refer to Instrument Panel Cluster Trim Plate Bezel Replacement .
  19. Install the steering column. Refer to Steering Column Replacement .
  20. Install the left knee bolster. Refer to Driver Knee Bolster Replacement .
  21. Install the left knee bolster bracket. Refer to Driver Knee Bolster Bracket Replacement .
  22. Enable the SIR system. Refer to SIR Disabling and Enabling .
  23. Install the right knee bolster bracket. Refer to Passenger Knee Bolster Bracket Replacement .
  24. Install the BCM. Refer to Body Control Module Replacement .
  25. Install the right knee bolster. Refer to Passenger Knee Bolster Replacement .
  26. Connect the battery negative cable(s). Refer to Battery Negative Cable Disconnection and Connection .