GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

B+, Seat Adjuster Switch

1

1

--

--

Front Vertical Motor Down Control

1

1

--

--

Front Vertical Motor Up Control

1

1

--

--

Horizontal Motor Forward Control

1

1

--

--

Horizontal Motor Rearward Control

1

1

--

--

Rear Vertical Motor Down Control

1

1

--

--

Rear Vertical Motor Up Control

1

1

--

--

Ground - Seat Adjuster Switch

--

1

--

--

1. Power seat inoperative

Circuit/System Description

The Power seat system is completely controlled through the seat adjuster switch. Battery voltage is supplied at all times to the seat adjuster switch from the PWR SEATS 30A circuit breaker that is located in the body fuse block. When the seat adjuster switches are in an inactive state, the switch contacts are closed to the switch ground circuit.

All seat motors are reversible. For example, when the seat horizontal forward switch is pressed to move the entire seat forward, battery voltage is applied through the switch contacts and the seat horizontal motor forward control circuit to the motor. The motor is grounded through the horizontal motor rearward switch contacts and the horizontal motor rearward control circuit to the motor. The motor runs in order to drive the entire seat forward until the switch is released. Moving the entire seat rearward works similarly to moving the entire seat forward, except that battery positive voltage and ground are applied on opposite circuits causing the motor to run in the opposite direction. All seat motors are powered this way.

Reference Information

Schematic Reference

    •  Driver Seat Schematics
    •  Passenger Seat Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Power Seats System Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Circuit/System Verification

Operate the power seat switches for the seat directional motors listed below in both directions. The seat should move in the commanded directions.

    • Seat Horizontal Motor
    • Seat Front Vertical Motor
    • Seat Rear Vertical Motor
If all power seat functions are inoperative, refer to the Seat Adjuster Switch Circuit Test.
If 1 or more of the seat adjuster motors operate, refer to the Seat Adjuster Motor Circuit Test.

Circuit/System Testing

Seat Adjuster Switch Circuit Test.

  1. Ignition OFF, disconnect the harness connector at the appropriate seat adjuster switch.
  2. Test for less than 5 ohms between the ground circuit terminal C and ground.
  3. If greater than the specified range, test the ground circuit for an open/high resistance.
  4. Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal F and ground.
  5. If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
  6. If all circuits test normal, test or replace the seat adjuster switch.

Circuit/System Testing

Seat Adjuster Motor Circuit Test

  1. Ignition OFF, disconnect the harness connector at the seat adjuster motor assembly.
  2. Connect a test lamp between the appropriate control circuit terminals listed below:
  3. • Horizontal motor terminal C and terminal D
    • Front vertical motor terminal E and terminal F
    • Rear vertical motor terminal A and terminal B
  4. Ignition ON, press the appropriate seat switch in the Forward and Rearward or Up and DOWN directions. The test lamp should turn ON when commanding the up and down or forward and rearward states.
  5. If the test lamp remains OFF for either of the commands, test the control circuits for a short to ground or an open/high resistance. If the circuits test normal, test or replace the seat adjuster switch.
  6. If all circuits test normal, test or replace the seat adjuster motor assembly.

Component Testing

Seat Adjuster Switch

  1. Ignition OFF, disconnect the harness connector at the seat adjuster switch.
  2. Test for infinite resistance between the B+ terminal F and each control terminal listed below with the switch in the open position:
  3. • Seat front vertical up control terminal H
    • Seat front vertical down control terminal G
    • Seat horizontal forward control terminal D
    • Seat horizontal rearward control terminal E
    • Seat rear vertical up control terminal B
    • Seat rear vertical down control terminal A
    If not the specified value, replace the seat adjuster switch.
  4. Test for less than 1 ohm between the B+ terminal F and each control terminal listed below with the switch in the closed position.
  5. • Seat front vertical up control terminal H
    • Seat front vertical down control terminal G
    • Seat horizontal forward control terminal D
    • Seat horizontal rearward control terminal E
    • Seat rear vertical up control terminal B
    • Seat rear vertical down control terminal A
    If greater than the specified range, replace the seat adjuster switch.
  6. Test for less than 1 ohm between the ground terminal C and each control terminal listed below with the switch in the open position.
  7. • Seat front vertical up control terminal H
    • Seat front vertical down control terminal G
    • Seat horizontal forward control terminal D
    • Seat horizontal rearward control terminal E
    • Seat rear vertical up control terminal B
    • Seat rear vertical down control terminal A
    If greater than the specified range, replace the seat adjuster switch.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Power Seat Switch Replacement
    •  Front Seat Adjuster Replacement