GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2008 🢒 HHR 🢒 Engine 🢒 Engine Controls and Fuel - 2.0L 🢒 Intake Manifold Replacement

Removal Procedure

    Object Number: 2074129 Size: SH
  1. Remove the radiator air baffle and deflector. Refer to Radiator Air Upper Baffle and Deflector Replacement.
  2. Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement.
  3. Remove the charge air cooler inlet pipe. Refer to Charge Air Cooler Inlet Pipe Replacement.
  4. Remove the oil level indicator tube. Refer to Oil Level Indicator and Tube Replacement.
  5. Disconnect the fuel feed line quick connect fitting to the fuel rail. Refer to Metal Collar Quick Connect Fitting Service.
  6. Disconnect the charge air valve solenoid vacuum lines (1).
  7. Disconnect the charge air valve solenoid vacuum electrical connector (2).

    8. Object Number: 2074135 Size: SH
  8. Disconnect the charge air bypass valve vacuum line (1).
  9. Disconnect the evaporative emission (EVAP) electrical connector (2) from the EVAP purge solenoid.
  10. Remove the (EVAP) hose from the (EVAP) hose clip (3).
  11. Disconnect the evaporative emission (EVAP) line quick connect fitting (4) from the EVAP purge solenoid. Refer to Plastic Collar Quick Connect Fitting Service.
  12. Disconnect the manifold absolute pressure (MAP) sensor electrical connector (5).

    13. Object Number: 1825523 Size: SH
  13. Reposition the brake booster vacuum hose clamp at the intake manifold.
  14. Remove the brake booster hose from the intake manifold.

    15. Object Number: 1717513 Size: SH
  15. Remove the knock sensor electrical connector (2) clip from the oil level indicator tube bracket.

    16. Object Number: 1825527 Size: SH
  16. Disconnect the engine wiring harness electrical connector (1) from the throttle actuator control (TAC) module.

    17. Object Number: 1825530 Size: SH
  17. Remove the charge air bypass valve solenoid bolts.
  18. Reposition the charge air bypass valve solenoid assembly out of the way.

    19. Object Number: 1825534 Size: SH
  19. Disconnect the fuel feed pipe fitting from the fuel pump.
  20. Remove the fuel feed pipe bolts.
  21. Remove the fuel feed pipe.
  22. Inspect the fuel feed pipe nut for damaged threads.
  23. Inspect the fuel feed pipe sealing bail for damage or debris.
  24. Replace the fuel feed pipe if any damage is found.

    25. Object Number: 2074160 Size: SH
  25. Remove the charge air bypass vacuum tank. Refer to Charge Air Bypass Valve Vacuum Tank Replacement.
  26. Remove the wiring harness connector (1) from the intake manifold brace.
  27. Remove the charge air bypass vacuum tank bolt (2) and nut (3).
  28. Remove the charge air bypass vacuum tank brace (4).

    29. Object Number: 2074193 Size: SH
  29. Remove the intake manifold brace bolt (1).
  30. Remove the intake manifold brace (2).

    31. Object Number: 2074201 Size: SH
  31. Remove the high pressure fuel pump bracket bolt (1).
  32. Remove the A/C line bracket bolt (2).

    33. Object Number: 2074218 Size: SH
  33. Remove the intake manifold bolts and nuts.
  34. Remove the intake manifold and place on a clean work surface.
  35. Remove the intake manifold gasket and discard.

    36. Object Number: 1825560 Size: SH
  36. If replacing the intake manifold perform the following steps, otherwise proceed to step 11 in the installation procedure.
  37. Remove the MAP sensor bolts (1).
  38. Remove the MAP sensor (2), ensure that the O-ring seal (3) is still attached on the sensor, if not remove the O-ring seal from the intake manifold.
  39. Remove the EVAP purge solenoid bolt (6).
  40. Remove the EVAP purge solenoid (5), ensure that the O-ring seal (4) is still attached on the sensor, if not remove the O-ring seal from the intake manifold.

    41. Object Number: 1825561 Size: SH
  41. Turn the intake manifold up side down.
  42. Remove the throttle body bolts.
  43. Remove the throttle body and seal.

Installation Procedure

    Object Number: 1825561 Size: SH
  1. If replacing the intake manifold perform the following steps, otherwise proceed to step 11.
  2. Inspect the throttle body seal and replace if necessary.
  3. Install the throttle body seal and position the throttle body.

    4. Notice: Refer to Fastener Notice in the Preface section.

  4. Install the throttle body bolts.

    5. Tighten
    Tighten the bolts to 10 N·m (89 lb in).

  5. Turn the intake manifold right side up.

    6. Object Number: 1825560 Size: SH
  6. Inspect the EVAP purge solenoid and MAP sensor O-ring seals, replace if necessary.
  7. Ensure that the EVAP purge solenoid O-ring seal (4) is installed on the EVAP purge solenoid (5).
  8. Install the EVAP purge solenoid (5) and bolt (6).

    9. Tighten
    Tighten the bolt to 10 N·m (89 lb in).

  9. Ensure that the MAP sensor O-ring seal (3) is installed on the MAP sensor (2).
  10. Install the MAP sensor (2) and bolts (1).

    11. Tighten
    Tighten the bolts to 10 N·m (89 lb in).


    Object Number: 2074218 Size: SH
  11. Install a NEW intake manifold gasket.
  12. Install the intake manifold to the studs.
  13. Install the intake manifold bolts and nuts.

    14. Tighten
    Tighten the bolts/nuts to 22 N·m (16 lb ft).


    Object Number: 2074201 Size: SH
  14. Install the A/C line bracket bolt (2).

    15. Tighten
    Tighten the bolt to 10 N·m (89 lb in).

  15. Install the high pressure fuel pump bracket bolt (1).

    16. Tighten
    Tighten the bolt to 10 N·m (89 lb in).


    Object Number: 2074193 Size: SH
  16. Install the intake manifold brace (2).
  17. Loosely install the intake manifold brace bolt (1).
  18. Tighten the intake manifold brace bolt (1).

    19. Tighten
    Tighten the bolt to 25 N·m (18 lb ft).


    Object Number: 2074160 Size: SH
  19. Install the charge air bypass vacuum tank brace (4).
  20. Install the charge air bypass vacuum tank nut (3) and bolt (2).

    21. Tighten
    Tighten the nut and bolt to 22 N·m (16 lb ft).

  21. Install the wiring harness connector (1) to the intake manifold brace.
  22. Install the charge air bypass vacuum tank. Refer to Charge Air Bypass Valve Vacuum Tank Replacement.

    23. Object Number: 1825534 Size: SH
  23. Lubricate the high pressure fuel pump fuel feed pipe connection threads with silicon free engine oil GM P/N 12345610 (Canadian P/N 993193) or equivalent.
  24. Place the fuel feed pipe on top of the intake manifold.
  25. Connect the fuel feed pipe fitting to the high pressure fuel pump.
  26. Install the fuel feed pipe bolts.

    27. Tighten

        • Tighten the bolts to 10 N·m (89 lb in).
        • Tighten the fitting to 30 N·m (22 lb ft).

    Object Number: 1825530 Size: SH
  27. Install the charge air bypass valve solenoid bolts.

    28. Tighten
    Tighten the bolts to 10 N·m (89 lb in).


    Object Number: 1825527 Size: SH
  28. Connect the engine wiring harness electrical connector (1) to the TAC module.

    29. Object Number: 1717513 Size: SH
  29. Install the knock sensor electrical connector (1) clip to the intake manifold brace.

    30. Object Number: 1825523 Size: SH
  30. Install the brake booster hose to the intake manifold.
  31. Position the brake booster vacuum hose clamp at the intake manifold.

    32. Object Number: 2074135 Size: SH
  32. Connect the manifold absolute pressure (MAP) sensor electrical connector  (5).
  33. Connect the (EVAP) line quick connect fitting (4) from the EVAP purge solenoid. Refer to Plastic Collar Quick Connect Fitting Service.
  34. Install the (EVAP) hose from the (EVAP) hose clip (3).
  35. Connect the (EVAP) electrical connector  (2) from the EVAP purge solenoid.
  36. Connect the charge air bypass valve vacuum line (1).

    37. Object Number: 2074129 Size: SH
  37. Connect the charge air valve solenoid vacuum electrical connector (2).
  38. Connect the charge air valve solenoid vacuum lines (1).
  39. Connect the fuel feed line quick connect fitting to the fuel rail. Refer to Metal Collar Quick Connect Fitting Service.
  40. Install the oil level indicator tube. Refer to Oil Level Indicator and Tube Replacement.
  41. Install the charge air cooler inlet pipe. Refer to Charge Air Cooler Inlet Pipe Replacement.
  42. Install the air cleaner assembly. Refer to Air Cleaner Assembly Replacement.
  43. Install the radiator air baffle and deflector. Refer to Radiator Air Upper Baffle and Deflector Replacement.