GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2000 🢒 Impala 🢒 HVAC 🢒 HVAC Systems - Manual 🢒 HVAC Compressor Clutch Does Not Engage

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. The A/C compressor relay output is disabled if engine coolant temperature is above 121°C (250°F). The engine coolant indicator will illuminate at this temperature.

  1. The HVAC control assembly is inoperative when the HVAC control unit does not respond to any operator control request to enable the A/C compressor. The blower motor may still operate independent of the A/C controls.

Step

Action

Yes

No

Schematic Reference: HVAC Compressor Control Schematics

DEFINITION: The A/C compressor clutch will not engage when an A/C request has been made and a Powertrain DTC has not been set.

1

Did you review the HVAC operation and perform the necessary inspections?

Go to Step 2

Go to HVAC Compressor Controls Circuit Description

2

  1. Start the engine.
  2. Observe the coolant temperature indicator.

Is the engine coolant temperature indicator illuminated?

Go to Cooling System Schematic Icons in Engine Cooling

Go to Step 3

3

Important: For A/C compressor operation, ambient air temperature must be above 3°C (36°F).

  1. Start the engine.
  2. Place the blower motor switch in the maximum speed position.
  3. Place the A/C switch in the ON position.
  4. Place the air temperature switch in the coldest position.

Does the A/C compressor operate?

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

Go to Step 4

4
  1. Park the vehicle in the shade.
  2. Open the windows in order to ventilate the interior of the vehicle.
  3. If the A/C system was operating, then allow the A/C system to equalize for approximately 2 minutes.
  4. Ensure that the ignition key is in the OFF position.
  5. Install the J 43600 ACR 2000 Air Conditioning Service Center.
  6. Record the ambient air temperature at the vehicle.
  7. Record readings of the low and high side STATIC pressures.
  8. Compare the low and high side pressure values with the allowable limits for the recorded ambient air temperature. Refer to .

Are the low and high side pressure values within the allowable limits for the recorded ambient air temperature, and within 103 kPa (15 psi) of each other?

Go to Step 5

Go to Leak Testing

5
  1. Turn ON the ignition, with the engine OFF.
  2. With a scan tool, observe the A/C high side pressure sensor parameter in the powertrain data list.
  3. Compare the A/C high side pressure on the scan tool to the high side pressure value on the ACR 2000.

Are the high side pressure values within 103 kPa (15 psi) of each other?

Go to Step 6

Go to Step 19

6

Is the HVAC control assembly inoperative?

Go to Step 10

Go to Step 7

7
  1. Start the engine.
  2. With a scan tool, observe the A/C Request Signal parameter in the powertrain data list 2.
  3. Place the blower motor switch in the maximum speed position.
  4. Place the mode switch in the MAX air position.
  5. Place the A/C switch in the ON position.

Does the scan tool indicate that the A/C request parameter is YES?

Go to Step 8

Go to Step 12

8

With a scan tool, observe the A/C Commanded parameter in the powertrain data list 2.

Does the scan tool indicate that the A/C Commanded parameter is ON?

Go to Step 9

Go to Step 29

9

With a scan tool, command the A/C compressor clutch relay ON and OFF.

Does the A/C compressor clutch relay turn ON and OFF with each command?

Go to Step 13

Go to Step 15

10

Test the ignition 3 voltage circuit to the HVAC control assembly for a short to ground, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 36

Go to Step 11

11

Test the ground circuit to the HVAC control assembly for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 36

Go to Step 27

12

With a scan tool, observe the A/C Switch parameter in the BCM Inputs.

Does the scan tool indicate that the A/C Switch parameter is ON?

Go to Step 28

Go to Step 17

13
  1. Turn OFF the ignition.
  2. Disconnect the A/C compressor clutch relay.
  3. Probe the switch side voltage supply circuit of the A/C compressor clutch relay with a test lamp that is connected to a good ground.

Does the test lamp illuminate?

Go to Step 14

Go to Step 22

14

Connect a 10-amp fused jumper wire between the switch side voltage circuit of the A/C compressor clutch relay and the A/C compressor clutch supply voltage circuit of the A/C compressor clutch.

Does the A/C compressor clutch engage?

Go to Step 25

Go to Step 18

15
  1. Turn OFF the ignition.
  2. Disconnect the A/C compressor clutch relay.
  3. Turn ON the ignition, with the engine OFF.
  4. Probe the coil side voltage supply circuit of the A/C compressor clutch relay with a test lamp that is connected to a good ground.

Does the test lamp illuminate?

Go to Step 16

Go to Step 21

16
  1. Connect a test lamp between the control circuit of the A/C compressor clutch relay and the coil side voltage supply circuit of the A/C compressor clutch relay.
  2. With a scan tool, command the A/C compressor clutch relay ON and OFF.

Does the test lamp turn ON and OFF with each command?

Go to Step 25

Go to Step 23

17

Test the A/C request signal circuit for a short to ground, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 36

Go to Step 27

18

Test the A/C compressor clutch supply voltage circuit at the A/C compressor clutch for a short to ground, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 36

Go to Step 20

19

Test the ground circuit of the A/C pressure sensor for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 36

Go to Step 24

20

Test the ground circuit of the A/C compressor clutch for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 36

Go to Step 26

21

Repair the coil side voltage supply circuit of the A/C compressor clutch relay. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 36

--

22

Repair the switch side voltage supply circuit of the A/C compressor clutch relay. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 36

--

23

Test the control circuit of the A/C compressor clutch relay for an open, or a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 36

Go to Step 29

24

Inspect for poor connections at the harness connector of the A/C High pressure sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 36

Go to Step 30

25

Inspect for poor connections at the A/C compressor clutch relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 36

Go to Step 31

26

Inspect for poor connections at the harness connector of the A/C compressor clutch coil. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 36

Go to Step 32

27

Inspect for poor connections at the harness connector of the HVAC control assembly. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 36

Go to Step 33

28

Inspect for poor connections at the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 36

Go to Step 34

29

Inspect for poor connections at the harness connector of the powertrain control module (PCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 36

Go to Step 35

30

Replace the A/C high pressure switch. Refer to in Heating, Ventilation and Air Conditioning.

Did you complete the replacement?

Go to Step 36

--

31

Replace the A/C compressor clutch relay.

Did you complete the replacement?

Go to Step 36

--

32

Replace the A/C compressor clutch coil. Refer to and in Heating, Ventilation, and Air Conditioning.

Did you complete the replacement?

Go to Step 36

--

33

Replace the HVAC control assembly. Refer to .

Did you complete the replacement?

Go to Step 36

--

34

Replace the BCM. Refer to in Body Control System.

Did you complete the replacement?

Go to Step 36

--

35

Important:  Perform the programming procedure for the PCM.

Replace the Powertrain Control Module (PCM). Refer to one of the following procedures:

    •  in Engine Controls - 3.4L
    •  in Engine Controls - 3.8L

Did you complete the replacement?

Go to Step 36

--

36

Operate the system in order to verify the repair.

Did you correct the condition?

System OK

Go to Step 4