Rear Seat Back Cushion Cover Replacement Non Folding

1. Remove the rear seat back. Refer to Rear Seat Back Replacement .
2. Remove the rear seat armrest, if equipped. Refer to Rear Seat Armrest Replacement .



3. Remove the hog rings from the rear seat back cover.



4. Reach inside of the rear seat back cover in order to unfasten the hook and the loop retainers securingthe rear seat back cover to the pad.



5. Remove the rear seat back cover from the pad.

1. Position the rear seat back cover to the pad.



2. Align the alignment marks on the rear seat back cover to the alignment marks on the pad.



3. Pull the rear seat back cover over the pad while alining the hook and the loop retainers.



4. Pull the rear seat back cover over the pad and pull over and under the edge.



5. Use firm hand pressure in order to fasten the hook and the loop retainers, securing the rear seat back cover to the pad.



6. Align the alignment marks on the rear seat back cover to the alignment marks on the pad, on the back side.



7. Install the hog rings to the rear seat back cover.
8. Install the rear seat armrest, if equipped. Refer to Rear Seat Armrest Replacement .
9. Install the rear seat back. Refer to Rear Seat Back Replacement .

Rear Seat Back Cushion Cover Replacement Folding

1. Remove the rear seat back. Refer to Rear Seat Back Replacement .
2. Remove the rear seat back bolsters. Refer to Rear Split Folding Seat Back Bolster Replacement .



3. Remove the bolts from the rear split folding seat back frame.



4. Remove the left rear seat back from the rear seat back frame.



5. Remove the right rear seat back from the rear seat back frame.



6. Unhook the J-hook retainers at the bottom of the right and/or left rear seat back.
7. Pull back the right and/or left carpet in order to expose the rear seat trim flaps in order to remove the staples.



8. Reach inside of the right and/or left rear seat back cover in order to unfasten the hook and loop retainers securing the rear seat back cover to the pad.
9. Remove the rear seat folding armrest, if equipped. Refer to Rear Seat Armrest Replacement .



10. Remove the right and/or left rear seat back cover from the rear seat back, by pulling the rear seat back cover up and over the pad.

1. Install the right and/or left rear seat back cover to the rear seat back, by pulling the rear seat back cover down and over the pad.
2. Reach inside of the right rear seat back cover and reposition the rear seat back release pullstrap through the rear seat back cover.
3. Aline the hook and the loop retainers.



4. Use firm hand pressure in order to fasten the hook and loop retainers, securing the rear seat back cover to the pad.
5. Install the rear seat folding armrest, if equipped. Refer to Rear Seat Armrest Replacement .



6. Reposition the rear seat back cable on the right rear seat back.
7. Reposition the rear seat trim flaps.



8. Install new staples to the rear seat trim flaps.



9. Fasten the J-hook retainer at the bottom of the right and/or left rear seat back.



10. Install the left rear seat back to the rear seat back frame.



11. Install the right rear seat back to the rear seat back frame.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

12. Install the split folding seat back frame bolts.

Tighten
Tighten the split folding seat back frame bolts to 10 N·m (89 lb in).

13. Install the rear seat back bolsters. Refer to Rear Split Folding Seat Back Bolster Replacement .
14. Install the seat back. Refer to Rear Seat Back Replacement .