Circuit Description
The body control module (BCM) controls the fog lamp relay. The BCM gets an input from the fog lamp switch input circuit and then energizes the fog lamp relay by grounding the fog lamp relay coil control circuit. The BCM will only ground the fog lamp relay coil control circuit if the following conditions exist:
| • | The ignition switch must be in the RUN position. |
| • | The headlamp switch must be in the PARK or HEAD position. |
| • | The headlamp dimmer switch must be in the LOW position. |
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC B2533 Front Fog Lamp Control Circuit High
Conditions for Running the DTC
The BCM must be commanding the fog lamp relay to energize.
Conditions for Setting the DTC
| • | The BCM detects a short to battery positive voltage in the fog lamp relay coil control circuit when the BCM tries to energize the fog lamp relay. |
| • | The condition above must be present for more than 0.3 seconds. |
Action Taken When the DTC Sets
The BCM stores DTC B2533 in memory.
Conditions for Clearing the DTC
| • | A current DTC B2533 will clear if the BCM no longer detects a short to battery positive voltage in the fog lamp relay coil control circuit. |
| • | A history DTC B2533 will clear after 100 consecutive ignition cycles if the condition for the malfunction is no longer present. |
Diagnostic Aids
| • | If the DTC B2533 is a history DTC, the fault may be intermittent. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems. |
| • | The following conditions may cause an intermittent malfunction to occur: |
| - | An intermittent short to battery in the fog lamp relay coil control circuit |
| - | The fog lamp relay coil is intermittently shorted to battery internally. |
| - | The BCM is intermittently shorted to battery internally. |
Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Fog Lights Schematics Connector End View Reference: Master Electrical Component List in Wiring Systems | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information |
2 |
Does the fog lamp relay turn ON and OFF with each command? | Go to Diagnostic Aids | Go to Step 3 |
3 |
Does the test lamp illuminate? | Go to Step 4 | Go to Step 10 |
4 |
Does the test lamp turn ON and OFF with each command? | Go to Step 8 | Go to Step 5 |
5 | Does the test lamp remain illuminated with each command? | Go to Step 7 | Go to Step 6 |
6 | Test the fog lamp relay control circuit for a short to battery positive voltage or an open. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 14 | Go to Step 9 |
7 | Test the fog lamp relay control circuit for a short to ground. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 14 | Go to Step 9 |
8 | Inspect for poor connections at the fog lamp relay. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 14 | Go to Step 12 |
9 | Inspect for poor connections at the harness connector of the body control module (BCM). Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 14 | Go to Step 13 |
10 | Test for a open or high resistance in the fog lamp relay coil side battery positive voltage supply circuit. Refer to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 14 | Go to Step 11 |
11 | Replace the underhood junction block. Refer to Underhood Electrical Center or Junction Block Replacement in Wiring Systems. Did you complete the repair? | Go to Step 14 | -- |
12 | Replace the fog lamp relay. Refer to Relay Replacement in Wiring Systems. Did you complete the replacement? | Go to Step 14 | -- |
13 | Replace the BCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup and programming. Did you complete the replacement? | Go to Step 14 | -- |
14 |
Does the DTC reset? | Go to Step 2 | System OK |
