GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2007 🢒 Impala 🢒 Body Hardware and Trim 🢒 Exterior Trim 🢒 Front Bumper Fascia Emblem Replacement

Front Bumper Fascia Emblem Replacement Base


Object Number: 1608322 Size: SF

Callout

Component Name

Fastener Tightening Specifications: Refer to Fastener Tightening Specifications .

1

Plate Assembly, Front Bumper Fascia Name

Important: When removing protective liners from adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.

Tip
Use a J 25070 or equivalent to remove the old nameplate. Clean all adhesive from front bumper fascia, wipe surface dry with a clean lint-free towel prior to installing new nameplate.

Front Bumper Fascia Emblem Replacement Impala/Monte Carlo SS


Object Number: 1608316 Size: SF

Callout

Component Name

Fastener Tightening Specifications: Refer to Fastener Tightening Specifications .

1

Plate Assembly, Front Bumper Fascia Name

Important: When removing protective liners from adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.

Tip
Use a J 25070 or equivalent to remove the old nameplate. Clean all adhesive from front bumper fascia, wipe surface dry with a clean lint-free towel prior to installing new nameplate.

Front Bumper Fascia Emblem Replacement Monte Carlo

Removal Procedure

Tools Required

J 25070 Heat Gun

  1. When replacing or repairing an emblem/nameplate do the following:
    2. 1.1. Use tape to protect the mounting surface during removal.
    1.2. Use tape for alignment marks for installation of the emblem/nameplate.
  2. To remove an emblem/nameplate, heat the emblem/nameplate using J 25070 . Apply heat using a circular motion for about 30 seconds.

    3. Object Number: 321645 Size: SH

    Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing an emblem/name plate.

  3. Use a plastic, flat-bladed tool to remove the emblem/nameplate from the panel surface.
  4. When replacing, remove all adhesive as follows:
    5. • For body panels use a 3M™ Scotch Brite molding adhesive remover disk 3M™ P/N 07501 or equivalent.
    • For plastic panels use a lint-free cloth and Varnish Makers and Painters (VMP) naptha or a 50/50 mixture by volume of isopropyl alcohol and water to remove the adhesive.

Installation Procedure

    Important: Apply the emblem/nameplate in an environment that is free from dust or other dirt that could come into contact with the sticky backing. Foreign material may cause improper adhesion.

  1. Clean the area where the emblem/nameplate will be installed.

    2. Use a lint free cloth and Varnish Makers and Painters (VMP) naptha or a 50/50 mixture by volume of isopropyl alcohol and water to clean the area.

  2. Dry the area thoroughly.

    3. Object Number: 461167 Size: SH
  3. Apply tape and mark the location as shown.
  4. Heat the mounting surface to approximately 27-41°C (80-105°F).
  5. Ensure that the temperature of the emblem/nameplate is approximately 29-32°C (85-90°F).
  6. Remove the protective liner from the back of the emblem/nameplate.
  7. Position the emblem/nameplate to the location marks and press the emblem/nameplate to the mounting surface.
  8. Apply equal pressure along the emblem/nameplate to uniformly bond the item to the mounting surface.
  9. Remove the protective tape from the mounting surface.