Fastener Tightening Specifications: Refer to Fastener Tightening Specifications .

1

Nameplate, Rear Compartment Lid (IMPALA)

Tip

1. When removing protective liners from adhesive tape backed nameplates, be careful not to touch the tape with hands and do not allow the tape to come in contact with dirt or any foreign matter prior to adhesion.
2. Use a J 25070 or equivalent to remove the old nameplate. Clean all adhesive from the rear compartment lid, wipe surface dry with a clean lint-free towel prior to installing the new nameplate.
3. Apply the new nameplate with the rear compartment lid in the closed position.
4. Apply pressure to the nameplate to ensure full adhesion is made to the compartment lid.

2

Nameplate, Rear Compartment Lid (Bowtie)

Tip

1. When removing protective liners from adhesive tape backed nameplates, be careful not to touch the tape with hands and do not allow the tape to come in contact with dirt or any foreign matter prior to adhesion.
2. Use a J 25070 or equivalent to remove the old nameplate. Clean all adhesive from the rear compartment lid, wipe surface dry with a clean lint-free towel prior to installing the new nameplate.
3. Apply the new nameplate with the rear compartment lid in the closed position.
4. Apply pressure to the nameplate to ensure full adhesion is made to the compartment lid.

3

Emblem, Rear Compartment Lid (SS)

Tip

1. When removing protective liners from adhesive tape backed emblems, be careful not to touch the tape with hands and do not allow the tape to come in contact with dirt or any foreign matter prior to adhesion.
2. Use a J 25070 or equivalent to remove the old emblem. Clean all adhesive from the rear compartment lid, wipe surface dry with a clean lint-free towel prior to installing the new emblem.
3. Apply the new emblem with the rear compartment lid in the closed position.
4. Apply pressure to the emblem to ensure full adhesion is made to the compartment lid.

Fastener Tightening Specifications: Refer to Fastener Tightening Specifications .

1

Nameplate, Rear Compartment Lid (IMPALA)

Tip

1. When removing protective liners from adhesive tape backed nameplates, be careful not to touch the tape with hands and do not allow the tape to come in contact with dirt or any foreign matter prior to adhesion.
2. Use a J 25070 or equivalent to remove the old nameplate. Clean all adhesive from the rear compartment lid, wipe surface dry with a clean lint-free towel prior to installing the new nameplate.
3. Apply the new nameplate with the rear compartment lid in the closed position.
4. Apply pressure to the nameplate to ensure full adhesion is made to the compartment lid.

2

Emblem, Rear Compartment Lid (LS LT LTZ)

Tip

1. When removing protective liners from adhesive tape backed emblems, be careful not to touch the tape with hands and do not allow the tape to come in contact with dirt or any foreign matter prior to adhesion.
2. Use a J 25070 or equivalent to remove the old emblem. Clean all adhesive from the rear compartment lid, wipe surface dry with a clean lint-free towel prior to installing the new emblem.
3. Apply the new emblem with the rear compartment lid in the closed position.
4. Apply pressure to the emblem to ensure full adhesion is made to the compartment lid.

3

Nameplate, Rear Compartment Lid (Bowtie)

Tip

1. When removing protective liners from adhesive tape backed nameplates, be careful not to touch the tape with hands and do not allow the tape to come in contact with dirt or any foreign matter prior to adhesion.
2. Use a J 25070 or equivalent to remove the old nameplate. Clean all adhesive from the rear compartment lid, wipe surface dry with a clean lint-free towel prior to installing the new nameplate.
3. Apply the new nameplate with the rear compartment lid in the closed position.
4. Apply pressure to the nameplate to ensure full adhesion is made to the compartment lid.

1

Flex Fuel Badge

Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section.

Procedure

1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
2. Use a J 25070 Heat Gun or equivalent to remove the old nameplate.
3. Clean all adhesive from rear compartment lid panel and wipe the surface dry with a clean lint-free towel prior to installing the new name plate.
4. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
5. Close the rear compartment lid prior to installing the nameplate.
6. Using the palm of the hand, wet out the name plate to the rear compartment lid panel and ensure full adhesion of the name plate is made.