Circuit Description
Ignition voltage is supplied directly to the malfunction indicator lamp (MIL). The engine control module (ECM) controls the lamp by grounding the control circuit through an internal switch called a driver. The primary function of the driver is to supply the ground for the component being controlled. Each driver has a fault line which is monitored by the ECM. When the ECM is commanding a component ON, the voltage of the control circuit should be low, near 0 volts. When the ECM is commanding the control circuit to a component OFF, the voltage potential of the circuit should be high, near battery voltage. If the fault detection circuit senses a voltage other than what is expected, the fault line status will change causing the DTC to set.
Conditions for Running the DTC
| • | The engine speed is more than 400 RPM. |
| • | The ignition voltage is between 6-18 volts. |
Conditions for Setting the DTC
| • | The ECM detects that the commanded state of the driver and the actual state of the control circuit do not match. |
| • | The conditions are present for a minimum of 5 seconds. |
Action Taken When the DTC Sets
| • | The control module stores the DTC information into memory when the diagnostic runs and fails. |
| • | The malfunction indicator lamp (MIL) will not illuminate. |
| • | The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Failure Records. |
| • | The driver information center, if equipped, may display a message. |
Conditions for Clearing the DTC
| • | A current DTC Last Test Failed clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other non-emission related diagnostic. |
| • | Clear the DTC with a scan tool. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step tests for a short to ground in the MIL control circuit. With the ECM disconnected and the ignition ON the MIL should be OFF.
-
This step tests for a short to voltage on the MIL control circuit. With the fuse removed there should be no voltage on the MIL control circuit.
-
This vehicle is equipped with a ECM that utilizes an electrically erasable programmable read only memory (EEPROM). When the ECM is being replaced, the new ECM must be programmed.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Engine Control Module Connector End Views or Engine Controls Connector End Views | ||||
1 | Did you perform the Diagnostic System Check-Engine Controls? | -- | Go to Step 2 | |
2 |
Does the MIL turn ON and OFF when commanded? | -- | Go to Step 3 | Go to Step 4 |
3 |
Does the DTC fail this ignition? | -- | Go to Step 4 | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems |
4 | Inspect the fuse that supplies battery positive voltage to the MIL. Is the fuse open? | -- | Go to Step 10 | Go to Step 5 |
Is the MIL OFF? | -- | Go to Step 6 | Go to Step 11 | |
Does the voltage measure the specified value? | 0 V | Go to Step 7 | Go to Step 12 | |
7 |
Does the MIL illuminate? | -- | Go to Step 15 | Go to Step 8 |
8 |
Does the test lamp illuminate? | -- | Go to Step 9 | Go to Step 13 |
9 | Test the MIL control circuit for an open or high resistance and repair as necessary. Refer to Wiring Repairs in Wiring Systems. Did you find and correct a condition? | -- | Go to Step 18 | Go to Step 14 |
10 | Repair the short to ground in the battery positive voltage circuit. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 18 | -- |
11 | Repair the short to ground in the MIL control circuit. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 18 | -- |
12 | Repair the short to voltage on the MIL control circuit. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 18 | -- |
13 | Repair the open in the MIL battery positive voltage circuit. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 18 | -- |
14 | Inspect for poor connections at the I/P and repair as necessary. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 18 | Go to Step 16 |
15 | Inspect for poor connections at the ECM and repair as necessary. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 18 | Go to Step 17 |
16 | Replace the I/P. Refer to Instrument Cluster Replacement in Instrument Panel, Gages and Console. Did you complete the repair? | -- | Go to Step 18 | -- |
Replace the ECM. Refer to Engine Control Module Replacement . Did you complete the repair? | -- | Go to Step 18 | -- | |
18 |
Does the DTC run and pass? | -- | Go to Step 19 | Go to Step 2 |
19 | With a scan tool, observe the stored information, Capture Info. Does the scan tool display any DTCs that you have not diagnosed? | -- | System OK | |
