GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2009 🢒 Kodiak C-Series (Conventional) C4/C5 🢒 Suspension 🢒 Air Suspension 🢒 Main Support Beam Replacement

Removal Procedure
  1. Block the wheels of the axle.
  2. Support the axle using jack stands.
  3. Drain the air pressure from the air springs.
  4. Remove the height control valve link from the valve.

    5. Object Number: 200651 Size: SH
  5. Remove the following components from the spring hanger:
    6. • The rebound bolt (4)
    • The locknut (1)
    • The washers
    • The spacer tube (2)
    • The rebound roller (3)
  6. Raise the rear of the frame far enough in order to remove the load from the main support beam.

    7. Object Number: 200654 Size: SH
  7. Remove the U-bolt locknuts (3) and the washers.
  8. Remove the following components:
    9. • The U-bolts (1)
    • The bottom pads (4)
    • The top pad (2)

    Object Number: 200660 Size: SH
  9. Remove the locknuts (4) and the washers that connect the cross channel (1) to both of the main support beams (3).
  10. Lift the cross channel off of the main support beam using jacks.
  11. Remove the main support beam assembly.

Installation Procedure

    Note: The Delrin liner must be positioned on the top side of the main support beam.

  1. Position the main support beam on the axle seat with the main support beam center dowel pin. Pilot the main support beam into the hole of the axle seat or the spacer plate.

    2. Object Number: 200654 Size: SH

    Note: Do not tighten the U-bolts at this time. Position the torque rod mounting bolts of the spring seats toward the front of the vehicle.

  2. Install the following components:
    3. • The top pad (2)
    • The U-bolts (1)
    • The bottom cap (4)
    • The washers
    • The locknuts (3)

    Object Number: 200660 Size: SH
  3. Lower the air spring and the cross channel mounting bolts into the main support beams (3).

    4. Caution: Refer to Fastener Caution in the Preface section.

  4. Install the washers and the locknuts (4) that connect the cross channel (1) to the main support beam (3).

    5. Tighten
    Tighten the locknuts in 37 N·m (50 lb ft) increments to 330 N·m (243 lb ft).

  5. Lower the frame in order to ensure that the spring hangers engage the main support beam.
  6. Refill air into the system.
  7. Center the tip of the main support beam between the spring hanger legs.

    8. Note: Do not exceed the specified torque on the U-bolt locknuts.


    Object Number: 200648 Size: SH
  8. Tighten the U-bolt nuts.

    9. Tighten
    Tighten the nuts in 37 N·m (50 lb ft) increments to 394 N·m (291 lb ft).

  9. Hit the top of the U-bolts using a hammer. Retighten the U-bolt nuts.

    10. Tighten
    Tighten the U-bolt nuts in 37 N·m (50 lb ft) increments to 394 N·m (291 lb ft).


    Object Number: 200651 Size: SH
  10. Install the following components in the hangers:
    11. • The rebound bolt (4)
    • The spacer tube (2)
    • The rebound roller (3)
    • The washers
    • The locknuts (1)

    Tighten
    Tighten the rebound bolt locknut to 82 N·m (61 lb ft).

  11. Unblock the wheels.
  12. Inspect the alignment after installing the new main support beams.