Circuit Description
The crankshaft position (CKP) sensor signal indicates the crankshaft speed and position. The CKP sensor is connected directly to the powertrain control module (PCM), and consists of the following circuits:
| • | The 12-volt reference circuit |
| • | The low reference circuit |
| • | The CKP sensor signal circuit |
If the PCM detects no signal from the CKP sensor for more than 3 seconds, DTC P0335 sets.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0335 Crankshaft Position (CKP) Sensor Circuit
Conditions for Running the DTC
| • | DTCs P0101, P0102, P0103, P0341, P0342, or P0343 are not set. |
| • | The camshaft position (CMP) sensor is transitioning. |
| • | The mass air flow (MAF) is more than 3 g/s in the crank mode. |
| • | The MAF is more than 5 g/s in the running mode. |
| • | This diagnostic runs continuously when the above conditions are met. |
Conditions for Setting the DTC
The PCM detects no signal from the CKP sensor for more than 3 seconds.
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step determines if the fault is present.
-
This step simulates a CKP sensor signal to the PCM. If the PCM receives the signal, the fuel pump will operate for about two seconds.
Step | Action | Values | Yes | No | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Component Connector End Views | ||||||||||||||||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |||||||||||||||
2 | Does the engine start and continue to run? | -- | Go to Step 3 | Go to Step 4 | ||||||||||||||
Did the DTC fail this ignition? | -- | Go to Step 4 | Go to Testing for Intermittent Conditions and Poor Connections | |||||||||||||||
4 |
Warning: Before proceeding, remove the fuses for the ignition coil and fuel injector feed circuits in order to prevent personal injury from engine rotation, sparks, and excessive engine fueling.
Note: An internally shorted CAM sensor can cause DTC P0335 to set. Test this circuit for a short before proceeding with this diagnostic table. Refer to Circuit Testing and Wiring Repairs. Does the DMM display the specified value? | B+ | Go to Step 5 | Go to Step 7 | ||||||||||||||
5 | Measure the voltage between the CKP sensor 12-volt reference circuit and the CKP sensor low reference circuit with the DMM. Does the DMM display the specified value? | B+ | Go to Step 6 | Go to Step 8 | ||||||||||||||
Momentarily connect the test lamp between the CKP sensor signal circuit and the CKP sensor 12-volt reference circuit. Does the fuel pump operate when voltage was applied to the CKP sensor signal circuit? | -- | Go to Step 11 | Go to Step 9 | |||||||||||||||
7 | Test for an open or a short to ground in the CKP sensor 12-volt reference circuit. Refer to Circuit Testing and Wiring Repairs. Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 14 | ||||||||||||||
8 | Test for an open or for high resistance in the CKP sensor low reference circuit. Refer to Circuit Testing and Wiring Repairs. Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 14 | ||||||||||||||
9 | Test the CKP sensor signal circuit for the following conditions:
Refer to Circuit Testing and Wiring Repairs. Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 10 | ||||||||||||||
10 | Inspect for poor connections at the CKP sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Repairing Connector Terminals. Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 14 | ||||||||||||||
11 |
Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 12 | ||||||||||||||
12 | Inspect the CKP reluctor wheel for the following conditions:
Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 13 | ||||||||||||||
13 | Replace the CKP sensor. Refer to Crankshaft Position Sensor Replacement. Did you complete the repair? | -- | Go to Step 16 | -- | ||||||||||||||
14 | Inspect for poor connections at the powertrain control module (PCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs. Did you complete the repair? | -- | Go to Step 16 | Go to Step 15 | ||||||||||||||
15 | Replace the PCM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 16 | -- | ||||||||||||||
16 |
Did the DTC run and pass? | -- | Go to Step 17 | Go to Step 2 | ||||||||||||||
17 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | System OK | |||||||||||||||
