Circuit Description
The accelerator pedal position (APP) sensor 1 is a potentiometer type sensor with the following 3 circuits
| • | A 5-volt reference circuit |
| • | A low reference circuit |
| • | A signal circuit |
The control module provides the APP sensor a 5-volt reference circuit and a low reference circuit. The APP sensor then provides the control module a signal voltage proportional to pedal movement. The APP sensor 1 signal voltage is low at rest and increases as the pedal is depressed. When the control module detects that the APP sensor 1 signal or APP sensor 5-volt reference voltage is outside the predetermined range, this DTC sets.
Conditions for Running the DTC
| • | DTC P0601, P0602, P0606, or P1518 are not set. |
| • | The ignition switch is in the crank or run position. |
| • | The ignition voltage is greater than 5.23 volts. |
Conditions for Setting the DTC
| • | APP sensor 1 voltage ranges between 0.25 volts and 4.22 volts. |
| • | All of the above conditions are present for less than 1 second. |
Action Taken When the DTC Sets
| • | The control module stores the DTC information into memory when the diagnostic runs and fails. |
| • | The malfunction indicator lamp (MIL) will not illuminate. |
| • | The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Failure Records. |
| • | If one or more APP sensor DTCs are set for a single APP sensor, the following occurs: |
| - | The control module will not command Reduced Engine Power mode. |
| - | The control module will use the remaining two APP sensors to calculate throttle response. |
| • | If certain multiple APP sensor DTCs are set for more than one APP sensor, the following occurs: |
| - | The control module commands Reduced Engine Power mode. |
| - | The APP indicated angle is limited to a predetermined value to limit the amount of throttle control. |
| - | The message center displays Reduced Engine Power. |
| • | If all three APP sensors are out of range, the following occurs: |
| - | The control module commands Reduced Engine Power mode. |
| - | The APP indicated angle is limited to 0 percent. The control module only allows the engine to idle. |
| - | The message center displays Reduced Engine Power. |
Conditions for Clearing the DTC
| • | A current DTC Last Test Failed clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other non-emission related diagnostic. |
| • | Clear the DTC with a scan tool. |
Diagnostic Aids
| • | Inspect the throttle actuator control (TAC) module connectors for signs of water intrusion. When this occurs, multiple DTCs could be set with no circuit or component conditions found during diagnostic testing. |
| • | When the TAC module detects throttle movement with a DTC P2120 set, a DTC P2121 also sets. |
| • | When the TAC module detects a condition within the TAC system, more than one TAC system related DTC may set. This is due to the many redundant tests run continuously on this system. Locating and repairing one individual condition may correct more than one DTC. Disconnecting components during testing may set additional DTCs. Keep this in mind when reviewing the stored information, Capture Info. |
| • | For an intermittent, refer to Intermittent Conditions . |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This test isolates whether the short is to another TAC system circuit in the harness or within the TAC module.
-
When the TAC module detects a condition within the TAC system, more than one TAC system related DTC may set. This is due to the many redundant tests run continuously on this system. Locating and repairing one individual condition may correct more than one DTC. Disconnecting components during testing may set additional DTCs. Keep this in mind when reviewing the stored information, Capture Info.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Powertrain Control Module Connector End Views or Engine Controls Connector End Views | ||||
1 | Did you perform the Diagnostic System Check-Engine Controls? | -- | Go to Step 2 | |
2 |
Important: If DTC P1518 or P0120 is also set, refer to the appropriate DTC for further diagnosis.
Does the scan tool indicate APP sensor 1 voltage within the specified values? | 0.25-2.24 V | Go to Step 3 | Go to Step 6 |
3 | Depress the accelerator pedal to the wide open throttle (WOT) position. Does the scan tool indicate APP sensor 1 voltage within the specified values? | 2.24-4.23 V | Go to Step 4 | Go to Step 6 |
4 |
Did this DTC fail this ignition during the above test ? | -- | Go to Step 24 | Go to Step 5 |
5 |
Did this DTC fail this ignition during the above test ? | -- | Go to Step 19 | Go to Diagnostic Aids |
6 | Disconnect the accelerator pedal position (APP) sensor harness connector. Does the scan tool indicate APP sensor 1 voltage at the specified value? | 0 V | Go to Step 7 | Go to Step 11 |
7 | Connect a test lamp between the APP sensor 1 signal circuit and B+. Does the scan tool indicate APP sensor 1 voltage at the specified value? | 5 V | Go to Step 8 | Go to Step 13 |
8 | Use a DMM in order to test the APP sensor 1 5-volt reference circuit for voltage. Does the DMM indicate voltage within the specified values? | 4.6-5.4 V | Go to Step 10 | Go to Step 9 |
9 |
Does the DMM indicate voltage within the specified values? | 4.6-5.4 V | Go to Step 21 | Go to Step 16 |
10 |
Does the scan tool indicate TP sensor 1 voltage at the specified value? | 0 V | Go to Step 19 | Go to Step 17 |
11 |
Did you find and correct the condition? | -- | Go to Step 25 | Go to Step 12 |
Did you find and correct the condition? | -- | Go to Step 25 | Go to Step 22 | |
13 |
Did you find and correct the condition? | -- | Go to Step 25 | Go to Step 14 |
14 | Use a DMM in order to test the APP sensor 1 signal circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 25 | Go to Step 15 |
15 |
Did you find and correct the condition? | -- | Go to Step 25 | Go to Step 22 |
16 |
Did you find and correct the condition? | -- | Go to Step 25 | Go to Step 22 |
17 |
Did you find and correct the condition? | -- | Go to Step 25 | Go to Step 18 |
18 | Use a DMM in order to test the TAC module ground circuit for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 25 | Go to Step 22 |
19 | Inspect for poor connections at the harness connector of the APP sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 25 | Go to Step 20 |
20 | Replace the APP sensor assembly. Refer to Accelerator Pedal Position Sensor Replacement . Did you complete the repair? | -- | Go to Step 25 | -- |
21 | Did DTC P0120 set while performing step 9? | -- | Go to DTC P0120 | Go to Step 22 |
22 | Inspect for poor connections at the harness connector of the TAC module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 25 | Go to Step 23 |
23 | Replace the TAC module. Refer to Electronic Throttle Actuator Control Module Replacement . Did you complete the repair? | -- | Go to Step 25 | -- |
24 | Repair the intermittent condition as necessary. Refer to Connector Repairs and Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 25 | -- |
25 |
Does the DTC run and pass? | -- | Go to Step 26 | Go to Step 2 |
With a scan tool, observe the stored information, Capture Info. Does the scan tool display any DTCs that you have not diagnosed? | -- | System OK | ||
