Circuit Description
The primary fuel level sensor and the secondary fuel level sensor change resistance in response to the fuel level. The ECM monitors the signal circuits of the primary fuel level sensor and the secondary fuel level sensor in order to determine the fuel level. When the fuel tanks are full, the resistances of both fuel level sensors are high, and the ECM senses a high signal voltage on both the signal circuits of the primary fuel level sensor and the secondary fuel level sensor. When the fuel tanks are empty, the resistances of the fuel level sensors are low, and the ECM senses a low signal voltage. The ECM uses the signal circuits of the primary fuel level sensor and the secondary fuel level sensor in order to calculate the percentage of remaining fuel in the tank. The ECM sends the fuel level percentage via the class II serial data circuit to the instrument cluster in order to control the fuel gage.
This diagnostic tests for a higher than normal secondary fuel level sensor signal.
Conditions for Running the DTC
| • | The ignition is ON. |
| • | The engine is running (LG4). |
Conditions for Setting the DTC
| • | The secondary fuel level signal is greater than 4.5 volts (LB7). |
| • | The secondary fuel level signal is greater than 98 percent (LG4). |
| • | The above condition is present for greater than 20 seconds. |
Action Taken When the DTC Sets
| • | The fuel gage defaults to empty. |
| • | The ECM records the operating conditions at the time that the diagnostic test fails. The ECM displays the failure information in the Failure Records on the scan tool. |
Conditions for Clearing the DTC
| • | The DTC becomes history when the conditions for setting the DTC are no longer present. |
| • | The history DTC clears after 40 malfunction free warm-up cycles. |
| • | The ECM receives the clear code command from the scan tool. |
Diagnostic Aids
| • | Use the Freeze Frame/Failure Records data in order to locate an intermittent condition. If you cannot duplicate the DTC, the information included in the Freeze Frame/Failure Records data may help in determining the number of miles since the DTC set. The Fail Counter and Pass Counter can also help in determining the number of ignition cycles that the diagnostic test reported a pass and/or fail. Operate the vehicle within the same freeze frame conditions, including those for RPM, for engine load, for vehicle speed, for temperature, and for others. This will isolate at what point the DTC failed. |
| Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems. |
| • | When the primary fuel level sensor signal is higher than normal, the Fuel Level Sensor % parameter in the ECM Fuel System data list on the scan tool indicates a value of about 100 percent. |
Test Description
The number below refers to the step number on the diagnostic table.
Step | Action | Value(s) | Yes | No | ||||
|---|---|---|---|---|---|---|---|---|
Schematic Reference: Instrument Cluster Schematics Connector End View Reference: Instrument Panel, Gages, and Console Connector End Views , Engine Control Module Connector End Views - LB7 or Engine Control Module Connector End Views - LG4 | ||||||||
1 | Did you perform the Instrument Cluster Diagnostic System Check? | -- | Go to Step 2 | |||||
2 |
Does the scan tool indicate that the fuel level sensor parameter is greater than the specified value? | 4.5 V (LB7 only) 98% (LG4 only) | Go to Step 3 | Go to Diagnostic Aids | ||||
Does the scan tool indicate that the fuel level sensor parameter is less than the specified value? | 0.5 V (LB7 only) 50% (LG4 only) | Go to Step 6 | Go to Step 4 | |||||
4 | Test the signal circuit of the secondary fuel level sensor for an open, for a high resistance, or for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 5 | ||||
5 | Test the low reference circuit of the secondary fuel level sensor for an open, for a high resistance, or for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 7 | ||||
6 | Inspect for poor connections at the harness connector of the secondary fuel level sensor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 8 | ||||
7 | Inspect for poor connections at the harness connector of the ECM. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 9 | ||||
8 | Replace the secondary fuel level sensor. Refer to:
Did you complete the replacement? | -- | Go to Step 10 | -- | ||||
9 |
Important: Program the replacement ECM. Replace the ECM. Refer to:
Did you complete the replacement? | -- | Go to Step 10 | -- | ||||
10 |
Does the DTC reset? | -- | Go to Step 2 | System OK | ||||
