The variable nozzle turbocharger (VNT) position sensor is a linear variable differential transtrometer type sensor. The VNT position sensor generates voltage according to VNT position and the generated voltage is input to the engine control module (ECM) for the VNT position sensor signal. The VNT position sensor has the following circuits:
• | The 5-volt reference circuit |
• | The low reference circuit |
• | The VNT position sensor signal circuit |
The ECM supplies 5 volts to the VNT position sensor on the 5-volt reference circuit. The ECM also provides a ground on the low circuit. The VNT position sensor provides a signal to the ECM on the VNT position sensor signal circuit which is relative to the position changes of the VNT. The ECM monitors the VNT position sensor signals for voltage outside the normal range of the VNT position sensor. If the ECM detects an excessively low VNT position sensor signal voltage, this DTC will set.
This diagnostic procedure supports the following DTC:
DTC P2564 Turbocharger Boost Control Position Sensor Circuit Low Voltage
• | The ignition is ON. |
• | The battery voltage is between 10-16 volts. |
The VNT position sensor signal circuit voltage is less than 0.1 volt.
• | The ECM illuminates the malfunction indicator lamp (MIL) and reduced engine power indicator lamp, if fitted, when the diagnostic runs and fails. |
• | The ECM records the operating conditions at the time the diagnostic fails. The ECM stores this information in the Failure Records. |
• | The ECM limits fuel injection quantity for fail-safe operation. |
• | The ECM closes the exhaust gas recirculation (EGR) valve and stops the EGR control. |
• | The ECM limits VNT control solenoid operation. |
• | The ECM inhibits cruise control. |
• | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
• | Clear the MIL and the DTC with a scan tool. |
• | If an intermittent condition is suspected, the following may cause an intermittent: |
- | Poor connections |
- | A misrouted harness |
- | Rubbed through wire insulation |
- | Broken wire inside the insulation |
• | Inspect for the following conditions: |
- | Poor connection at ECM--Inspect the harness connectors for the following conditions: |
• | Backed-out terminals |
• | Improper mating |
• | Broken locks |
• | Improperly formed or damaged terminals |
• | Poor terminal to wire connection |
- | Damaged harness--Inspect the wiring harness for damage. If the harness appears to be OK, observe the DTC P2564 display on the scan tool while moving the connectors and the wiring harness related to the sensor. A change in the display will indicate the location of the fault. |
Step | Action | Values | Yes | No |
---|---|---|---|---|
Schematic Reference: Engine Controls Schematics | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 3 | |
2 |
Is DTC P0641 also set? | -- | Go to DTC P0641 | Go to Step 3 |
3 |
Is the vane position sensor parameter less than the specified value? | 10% | Go to Step 4 | Go to Step 5 |
4 |
Did the DTC fail this ignition? | -- | Go to Step 5 | Go to Diagnostic Aids |
5 |
Is the DMM voltage within the specified range? | 4.5-5.5 V | Go to Step 6 | Go to Step 5 |
6 |
Is the vane position parameter more than the specified value? | 90% | Go to Step 9 | Go to Step 7 |
7 |
Did you find and correct the condition? | -- | Go to Step 9 | Go to Step 8 |
8 |
Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 10 |
9 |
Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 10 |
10 |
Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 12 |
11 | Replace the VNT position sensor. Refer to Turbocharger Vane Position Sensor Replacement . Did you complete the replacement? | -- | Go to Step 13 | -- |
12 |
Important: The new ECM must be programmed. Replace the ECM. Refer to Engine Control Module Programming and Setup , Engine Control Module Replacement/Restore Fuel Rate Data , and Fuel Injector Flow Rate Programming . Did you complete the replacement? | -- | Go to Step 13 | -- |
13 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 14 |
14 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | System OK |