Valve Rocker Arm Cover Replacement Left Side

1. Remove the accessory drive belt. Refer to Drive Belt Replacement .
2. Remove the engine mount strut at the engine. Refer to Engine Mount Strut Replacement .
3. Rotate the engine. Refer to Rotating the Engine for Service Access .
4. Disconnect the electrical connectors from the ignition coil.
5. Remove the ignition coil.
6. Remove the plastic cover from the shock tower.
7. Remove the generator front and rear braces. Refer to SECTION 6D3.
8. Remove the generator. Refer to SECTION 6D3.



9. Disconnect the EGR valve. Move the EGR valve aside.



10. Remove the right valve rocker arm cover bolts.
11. Remove the right valve rocker arm cover.
12. Remove the right valve rocker arm cover gasket.
13. Clean the cover and cylinder head gasket surface.

1. Install the new rocker arm cover gasket.
2. Apply sealant, GM P/N 12345739 or equivalent, at the cylinder head to lower manifold joint.
3. Install the right rocker arm cover.
4. Hand tighten the rocker arm cover bolts.

Tighten
Tighten the rocker arm cover bolts to 10 N·m (89 lb in).




5. Install the EGR valve.
6. Install the generator. Refer to SECTION 6D3.
7. Install the generator front brace and the generator rear brace.
8. Install the plastic cover to the shock tower.
9. Install the ignition coil.
10. Install the electrical connectors to the ignition coil.
11. Rotate the engine. Refer to Rotating the Engine for Service Access .
12. Install the engine mount strut at the engine. Refer to Engine Mount Strut Replacement .
13. Install the accessory drive belt. Refer to Drive Belt Replacement .

Valve Rocker Arm Cover Replacement Right Side

1. Drain the engine coolant.
2. Remove the air cleaner and duct.



3. Remove the thermostat bypass pipe clip nut.
4. Remove the automatic transaxle vacuum modulator pipe. Refer to SECTION 7A.
5. Remove the right engine mount strut at the engine. Refer to Engine Mount Strut Replacement .
6. Disconnect the upper radiator hose at the engine.



7. Remove the PCV valve from the cover.
8. Remove the heater outlet hose.
9. Remove the thermostat bypass pipe.
10. Remove the left rocker arm cover bolts.
11. Remove the left rocker arm cover.
12. Remove the left rocker arm cover gasket.
13. Clean the cover and cylinder head gasket surfaces.

1. Install a new gasket.
2. Install the left rocker arm cover.

Important: Apply sealant, GM P/N 12345739, or equivalent, at the cylinder head to lower manifold joint.

3. Hand tighten the valve rocker arm cover bolts.

Tighten
Tighten the bolts to 10 N·mmm (89 lb in).

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

4. Install the heater outlet hose.
5. Install the thermostat bypass pipe.
6. Install the PCV valve to the cover.
7. Connect the upper radiator hose at the engine.
8. Install the right engine mount strut at the engine. Refer to Engine Mount Strut Replacement .
9. Connect the automatic transaxle vacuum modulator pipe. Refer to SECTION 7A.



10. Install the thermostat bypass pipe clip nut.
11. Install the air cleaner and duct.
12. Refill with engine coolant. Add two engine coolant sealant pellets, GM P/N 3634621, or equivalent.
13. Bleed the cooling system. Refer to SECTION 6B.