DTC P1654 Air Conditioning (A/C) Clutch Relay Control Circuit. Chevrolet Lumina 1996

For 1990-2009 cars only

Makes 🢒 Chevrolet 🢒 1996 🢒 Lumina 🢒 DTC 🢒 DTC P1654 Air Conditioning (A/C) Clutch Relay Control Circuit

Refer to

HVAC A/C Control

Engine Controls Components
Powertrain Control Module Controlled Air Conditioning
Engine Cooing Fans
AIR ,Gen Control Volts Lamp, Low Oil
OBD II Symbol Description Notice
Handling ESD Sensitive Parts Notice
.

Output Driver Modules (ODMs) are used by the PCM to turn on many of the current-driven devices that are needed to control various engine and Transaxle functions. Each ODM is capable of controlling up to 7 separate outputs by applying ground to the device which the PCM is commanding ON. Unlike the Quad Driver Modules (QDMs) used in prior model years, ODMs have the capability of diagnosing each output circuit individually. DTC P1654 set indicates an improper voltage level has been detected on ODM B output 4, which controls the A/C compressor control relay.

Conditions for Setting the DTC

•	Ignition is ON.

•	An improper voltage level has been detected on ODM B output 4 (the A/C relay driver circuit).

•	Above conditions for at least 30 seconds.

Action Taken When the DTC Sets

•	The PCM will not illuminate the malfunction indicator lamp (MIL).

•	The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as Freeze Frame data.

Conditions for Clearing the MIL/DTC

•	A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.

•	The DTC can be cleared by using the scan tool Clear Info function.

Diagnostic Aids

Check for the following conditions:

•	Poor connection at PCM. Inspect harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and poor terminal to wire connection.

•

Damaged harness. Inspect the wiring harness for damage. If the harness appears to be OK, disconnect the PCM, turn the ignition ON and observe a J 39200 connected to the A/C relay driver circuit at the PCM harness connector while moving connectors and wiring harnesses related to the A/C relay. A change in voltage will indicate the location of the fault.

Reviewing the Fail Records vehicle mileage since the diagnostic test last failed may help determine how often the condition that caused the DTC to be set occurs. This may assist in diagnosing the condition.

Test Description

Number(s) below refer to the step number(s) on the Diagnostic Chart.

Normally, ignition feed voltage should be present on the output driver circuit with the PCM disconnected and the ignition turned ON.

Checks for a shorted component or a short to B+ on the output driver circuit. Either condition would result in a measured current of over 1.5 amps. Also checks for a component that is going open while being operated, resulting in a measured current of 0 amps.

Checks for a faulty A/C relay.

This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM is being replaced, the new PCM must be programmed. Refer to Powertrain Control Module Replacement/Programming .

DTC P1654 - A/C Relay Control Circuit

Step	Action	Value(s)	Yes	No
1	Was the Powertrain On-Board Diagnostic System Check performed?	--	Go to Step 2	Go to the Powertrain On Board Diagnostic (OBD) System Check
2	Turn OFF the ignition switch, disconnect the PCM. Turn ON the ignition switch. Using DVM (J 39200), measure voltage the A/C relay driver circuit at the PCM harness connector and ground. Is voltage near the specified value?	B+	Go to Step 3	Go to Step 6
3	Set J 39200 digital voltmeter (DVM) to measure 10 amp range. Measure current between the A/C relay driver circuit and ground. Monitor the current reading on the DVM for at least 2 minutes. Does the current reading remain between the specified values?	0.1-1.5 Amps	Go to Step 11	Go to Step 4
4	Disconnect the A/C relay (leave the PCM disconnected). Using DVM, measure voltage between the A/C relay driver circuit and ground. Is voltage at the specified value?	0V	Go to Step 14	Go to Step 5
5	Locate and repair short to voltage in the A/C relay driver circuit. Refer to Repair Procedures in Electrical Diagnosis. Is action complete?	--	Go to Step 16	--
6	Check the ignition feed fuse for the A/C relay Is the fuse blown?	--	Go to Step 7	Go to Step 8
7	Locate and repair short to ground in ignition feed circuit for the A/C relay. Refer to Fuse Block Details in Electrical Diagnosis. Replace fuse. Is action complete?	--	Go to Step 16	--
8	Disconnect the A/C relay. Turn ON the ignition switch, measure voltage between the ignition feed circuit for the A/C relay and ground. Is voltage near the specified value?	B+	Go to Step 9	Go to Step 13
9	Check the A/C relay driver circuit for an open or a short to ground. If a problem is found, repair the A/C relay driver circuit. Refer to Repair Procedures in Electrical Diagnosis. Was a problem found?	--	Go to Step 16	Go to Step 10
10	Check the output driver circuit and the ignition feed circuit for a poor connection at the A/C relay and at the PCM. If a problem is found, replace faulty terminal(s). Refer to Repair Procedures in Electrical Diagnosis. Was a problem found?	--	Go to Step 16	Go to Step 14
11	Turn OFF the ignition switch, reconnect the PCM and disconnect the A/C relay. Turn ON the ignition switch, connect J 34142-B test light between the affected output driver circuit and the ignition feed circuit at the A/C relay harness connector. Using the scan tool outputs test function, cycle the A/C relay ON and OFF. Does the test light flash ON and OFF?	--	Refer to Diagnostic Aids	Go to Step 12
12	Check the A/C relay driver circuit for a poor connection at the PCM. If a problem is found, replace faulty terminal. Refer to Repair Procedures in Electrical Diagnosis. Was a problem found?	--	Go to Step 16	Go to Step 15
13	Locate and repair open in ignition feed circuit to the A/C relay. Refer to Repair Procedures in Electrical Diagnosis. Is action complete?	--	Go to Step 16	--
14	Replace the A/C relay. Is action complete?	--	Go to Step 16	--
15	Replace the PCM. Important: Replacement PCM must be programmed. Refer to Powertrain Control Module Replacement/Programming . Is action complete?	--	Go to Step 16	--
16	Review and record scan tool Fail Records data. Clear DTCs. Operate vehicle within Fail Records conditions as noted. Using a scan tool, monitor Specific DTC info for DTC P1654 until the DTC P1654 test runs. Note test result; does scan tool indicate DTC P1654 failed this ign?	--	Go to Step 2	System OK